Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
Hello,
We are using the Message Routing API of nrfCloud to consume messages via Webhook and DLQ. We have several devices placed in different device groups (e.g. prod_devices...
Somewhat related to this:
I'm wishing to optimise code (removing a load of volatiles) by ensuring most of my application code runs at the same interrupt as the NRF_SDH_BLE_OBSERVER...
Hi,
I have 2 problems in power profiler kit II:
Problem 1: When I connect the porfiler kit II to the computer, the computer can't identify the PPK2
Porblem 2: The output...
I want to know how to adjust the TX RX setting for the nRF52833 DK connected to the nRF21540 EK shield. I have already added -DSHIELD="nrf21540ek" to the build configuration...
Hello.
I am trying to repeat the functionality of the project that is shown in this video https://www.youtube.com/watch?v=fCU8x-pmtqU&list=PLx_tBuQ_KSqG-leiJDfOKf_ZmCqHnbi4r&index...
We are using SDK v2.6.1 for our application, along with the Fanstel module WT02C40C.
Internet connectivity is provided to the WT02C40C module via a hotspot, with CONFIG_STA_KEY_MGMT_WPA2...
The "nRF Command Line Tools" page, https://www.nordicsemi.com/Products/Development-tools/nrf-command-line-tools says " Important: The nRF Command Line Tools is in the process...
I want to interface 3 custom made heater boards to nrf5340dk. Where the simple task is to toggle gpio's to Turn ON & OFF the heater board. Now, we are using P 0.01, 0.02 &...
Hello, I am considering the prospect of using channel sounding as opposed to UWB for indoor asset tracking. I can understand, that the main limitation with that would be,...
Hi There:
I used the nRF7002 DK to evaluate its WiFi throughput performance.
The test environment is below:
1. nRF7002 DK
2. NCS version: 2.5.0
3. Sample application...
Hello Everyone,
I have configured SPI1 at 1MHz, to receive data with a sensor. Basically i am reading data from a sensor device. So calling spi_transceive_dt() with 4...
The current specifications (v0.8) for the nRF54L series of parts provide very little information about the input impedance of the SAADC peripheral. There are no values specified...
hey i am using a custom nrf52840 board and i keep my device on by setting a gpio pin high and device turns off as soon as it sets to low .
during ota update when the bootloader...
Hi,
I have a firmware project that was originally developed for an nRF52833. It successfully mounts LittleFS on 3 partitions in external flash. For the nRF52833 I was simply...
