I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
Hello,
I am having difficulties reading the ICCID of a solder sim that is connected to a B1 revision of the NRF9160. I have tried two different NRF9160s, two different solder...
We're getting this strange AppError that is supposedly coming from the SD (considering the PC is correct)
App error: id: 0x00000001, pc: 0x0001505C, code: 0x00000715
I...
It looks like the DK comes with a coin cell type battery and there seems to be a tab that can be pulled off to activate. Can someone explain how to switch into battery mode...
Hi,
Which BLE dongle can we use on PC in order to communicate with nRF52810 and nRF52832 chips?
Is there a desktop version of "nRF uart app" for reading and writing...
Hi all!
I want to run OTA DFU over Thread from a RPi3. Previous tests from a PC were successful.
I installed nrftuil: sudo pip3 install nrfutil==5.2.0
I added the...
Hello.
I am wanting to send an infrared signal from my nrf52 DK (pca10040). I've found code online for sending custom IR signals using pwm and a gpio pin. The IR signals...
Hi! We're developing an app which connects to BLE devices for different purposes. We've successfully enabled MITM using windows(an example from Microsoft) , but are having...
Hey, I'm trying to install the cat tracker application. When I'm executing the npm ci command. It is prompting the following error
ubuntu@ip-172-31-25-55:~/aws/nrf-asset...
I am trying to code a cycle power service and I need to add a server characteristic configuration descriptor. This service is probably the only BT SIG service that uses that...
Hi, I am trying to get the voltage level of the battery using the AT_command AT%XVBAT which I tested using the at_client sample. I tried integrating it with my current code...
From looking at the code when a message is posted to "all-nodes" fixed group address of 0xFFFF it does not route. I was unable to find this behavior specified anywhere in...
Hi forum,
I am working on nrf52832, using sdk 15.0.0. I want to send the data(command) from esp32 to nRF52832 through Rx ,Tx . I have done connections rx,tx,gnd . I can...
Hi,
We are developing our stack with soft device using nRF52840 as the Controller and have the below queries
1. How to configure a static random BDADDR which will remain...
The error is
CMake Error at ../../../cmake/extensions.cmake:416 (add_library):
No SOURCES given to target: drivers__spi
This similar to
https://devzone.nordicsemi...
