I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
hi ,we have test the example of ble_app_att_mtu_throughput in nrf52840 ,the other side device is an android phone .
nrf52840 would freeze when the phone want to feature request...
Hello! I'm calculating the matching circuit with the antenna for nRF52832, but nowhere can I find the impedance value of the pins of the radio part, can you help me?
Hi,
I'm working with a nrf51822 based hardware which came programmed with some UUIDs and S110V7. Erased it completely, experimented with some non SD code first and finally...
Hello! I have a problem with checking the microcontroller nRF52832. J-Link does not connect to nRF52832, the screenshot of the Segger-commander window is shown below:
...
Bit of an odd question but Im dealing with a rather wonky SPI peripheral and its got me trying to sort some interesting questions due to its strange data protocol. Im using...
We are using the Android nRF toolbox v2.4.0 and have successfully implemented the Template app. The app will reliably connect with our device and functions well. The only...
Hi,
I was wondering if the SPI configuration for the p_config->sck_pin is correct. It appears that the clock is configured as output with input connected. Wouldn't this...
I am searching for long time how to inspect the prints in my code inside Segger , I went over many messages in this forum and nothing comes easy to me with this Segger thing...
Using Segger , only the BLE template is advertising,All other BLE apps such as BLE_UART, will flash the leds very fast but will not show on any Apple device on the Bluetooth...
We have an ISR parsing incoming serial data from the UART. When a valid packet arrives, I'd like to be able to wake the core from whatever low-power state is entered when...
That is probably an old topic, but after doing some research I could figure it out: calling sd_app_evt_wait() on my nRF5832 + nRF5 v11.0.0 SDK + s132 causes my chip to reset...
Hi
I've some troubles with the ble disconnection of S110.
Always when I call the sd_ble_gap_disconnect function after successful connected, the error code 8 NRF_ERROR_INVALID_STATE...
As I can see, I flashed Zephyr to Carbon 96 board, I don't fully understand the process,
I mean, I see .bin and .elf files but i don't see boot.img file, how do i make a...
The nRF52832 datasheet refers to a transmission of multiple packets in Figure 37. I have attempted to load multiple packets to the radio FIFO using nrf_esb_write_payload(...
