I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Just purchased a nPM1300 v1.1.0, but it will not connect to my computer. I am using version 2.6.1 of nrf connect, v1.3.0 of the PowerUp app, and what I believe is the correct...
Once the modem is turned off (e.g. using at+cfun=0) - what will be the state of the MAGPIO pins? Will they be pulled to GND or will they float?
Thanks
Ulf
P.S. The same...
Hi,
I am trying to implement the scan delegator in the broadcast_sink of the nRF5340 audio application.
Currently, I am adding the advertising feature in the broadcast_sink...
Hello, Our application image became too large for TF-M and we're investigating the use of PSA Protected Storage without TF-M as described in NCS 2.6.0.
When writing a new...
Hi,
I encountered a modem fault (NCS v2.5.1, mfw 1.3.4, nrf9160DK). Here's a portion of the log leading to the fault:
[24:36:01.333,312] <inf> gnss: event NRF_MODEM_GNSS_EVT_PVT...
Hello!
I am a beginner and am trying out an MQTT example on my nRF9161 DK that I recently bought in my Visual Studio Code on Windows 11. I am aware that the sample application...
Hi,
I am able to get my CA certificate working using TLS for MQTT. but im not able to get the TLS Client certificate working.
I had created a client certificate as per...
Hello, I'm following along the nRF Asset Tracker guide and I'm on the step 'Create device credentials'
Running the command
' ./cli.sh create-and-provision-device-cert...
Hello support.
A new design is looking at using nRF24L01+ to communicate wirelessly. I'm aware that this IC is no longer recommended for new designs, however, it's the one...
Hello,
I am trying to use the LTE modem serial example on a customized board that communicates an NRF9160 SICA B1 with an external STM32 microcontroller through the UART...
I am using the nRF52840 with NCS SDK v2.5.1. I tried to implement non-volatile storage in my application, and it is working on the DK board, but the code is not working on...
Hello,
I am using the DK Buttons and LEDs module to get the status of my button on the ANNA-B402C ( nRF52833 ).
I wanted to check if any debounce filter/mechanism software...
Hello,
as mentioned in the subject, I want to use single bank while CONFIG_BOOTLOADER_MCUBOOT=y. The reason is that the nRF7002 firmware is so large, it would cause an overflow...
Hello everyone,
I'm experiencing difficulties flashing my Seeeduino XIAO BLE Sense board using the nRF52840 Development Kit (DK) from Nordic Semiconductor. Despite correct...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0 ]
I want to debug using the Logger module...