I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
Hi, I'm trying to send 64-byte reports for INPUT and OUTPUT: 1 byte for report ID and 63 bytes of data. However, the HID service code doesn't seem to handle incoming OUTPUT...
Getting error: board.h and other header no such file or directory. with nRF5_SDK_15.0.0_a53641a and nrf5sdkformeshv500src in the same path.
What could it be?
The evaluation...
I'm writing my own lightweight bootloader for nRF5340 (which may or may not turn out to be a good idea). I have something similar that I'm using successfully on nRF52832 based...
When I use the command to read the software version, the message read by the Raspberry Pi does not appear " SoftwareVersion ".
Please confirm the attached LOG message
Hello,
I have a question about performing OTA via BLE (SMP) and using BLE mesh. Is it possible to perform OTA via BLE to ZigBee network and vice versa.
Since BLE is supported...
Hello,
I'm encountering issues while trying to install and update the nRF Connect SDK (NCS) environment on my macOS system.
NCS versions attempted: 2.2.0, 2.6.1
...
I am using nrf52840 to test the `periodic_adv_rsp` sample application using ncs. I had this use case where I would like to configure data in a subevent based on responses...
Hi Nordic community,
I'm starting this course as I'd like to start with Nordic.
I can't continue (better to say, start) the course as the instructions are different from...
Hello, I have an eval board of " nPM1100-EK -> PCA10123 0.8.0 " battery of li-po 3.7v 600mah battery termination voltage is 4.2V The above eval board works fine & the battery...
Greetings,
I'm trying to migrate the MAKEFILE configuration to SEGGER studio so that I could build and debug the project from there. So far, I'm stuck on the Linking part...
We are currently working on a Zigbee-based network coordinator using the nRF52840. I have a function, dfu_multi_image_write , that writes data to NVS in chunks. The function...
The Power Profiler app v4.2.0 release notes say:
"Updated PPK2 firmware to v1.2.0, which adds COM port for shell access"
Are there any instructions available how to use...
Hi,
My application is running NCS v2.5.3 on a nRF5340.
My project has FOTA via BLE, is running mcuboot, and is a multi-image build. I am trying to verify, from within...
Hello, I am trying to subscribe on a topic to get retained message.
I am using ncs 2.7.0
The problem is that whenever I am trying to subscribe to a certain topic, I have...
Dear all,
For a project we need to synchronize up to 5 data loggers, each of them is based on nRF52840. The sampling rate of some sensors can be of 1 kHz. I'm wondering...
