Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hello
I'm configuring Ping with AT command using API - nrf9160DK, zephyrOS. However, it doesn't go well. API reply "ERROR".
some other AT command goes well, but, Ping...
Hi, I am using the nRF52840 dongle + nRF Connect for Desktop App, and I would like to configure the data rate for packet advertising. Is this possible? Which one is set by...
I would like to use the cURL libary that is included in the nRF Connect SDK (v2.6.1) a nrf/ext/curl
I started with the download sample (nrf/samples/net/download)
I've...
Hello,
I am using matter SDK v2.7.0, when I run command below:
west zap-generate -z ~/Work/matter/light_switch/src/light_switch.zap -m /opt/nordic/ncs/v2.7.0
I get...
Hello, I designed custom board using nRF52832. But dfu is not working on that board. All other code is working fine. I am attaching schematic file of nordic part for reference...
Hi,
To prepare our new device, we are using a nrf5340dk board.
For our application, we need to perform DFU over BT.
Si, i following the tutorial https://academy.nordicsemi...
Hi,
we have been trying to implement modem delta updates to our nrf9160 project using DFU target. We send delta .bin file over LTE to our device, and save it to external...
Hi,
I want nRF91 to download the nrf52840 firmware update image from nrf cloud and then pass it to nRF52 using SMP over UART.
1.How can I use the nrf cloud FOTA UI...
When I program an interrupt, the NRF52840 requires 250uA extra. I read something about the sense interrupt, but I cannot find any working example. How should I implement an...
Hi,
I am working with Thingy53 using the ESB (Enhanced ShockBurst) library. I have my basic app running with multi-point comms and power control. This was done without using...
Hello,
We have a product which is a custom nRF52832 board, nRF5 SDK (didn't have time to upgrade to nRF Connect SDK), s132, BLE.
We used to call delete_bonds() function...
I‘m tring to run nRF5340 Audio applications with two nRF5340 Audio boards, following at: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.6.0/nrf/applications/nrf5340_audio...
I'm using the async API for UART and I have noticed that, shortly after initialisation, I receive a single character with the UART_RX_READY event. This character is 0xff ...
Dear all,
I kindly ask you what is such warning that arise in building the configuration for the NCS example, please point me to better understand why arise and the related...
