I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
I am trying to make a multiprotocol network using BLE and Thread. I have flashed nRF52840DK using the `s140` Softdevice and flashed the ble_thread_dyn_template as well.
...
Hi,
I am currently using the NRF52840 DK to evaluate the NFC functionalities of the SoC. It works very well with a smartphone.
I'd like to understand the NFC on the NRF52840...
Hi,
We are developing a matter curtain product the power by battery.I setup SED mode for low power. The larger the POLL PERIOD value I set , the worse the real-time performance...
Dear Support team
I don't quite understand the part as the picture below after I read the specification, I would like to kown What are the output drive modes in the picture...
I want to make an NFC card with Ntag 213, which is an NFC Type 2 tag.The card needs to write data to a specific block via NFC.
However, the NFC Type 2 tag library does not...
Hi, as stated at page 15 in the Direction Finding white paper(nWP-036), it says 'When the last switch pattern is reached and IQ sampling continues, the switch pattern loops...
//nRF52840 DK//PCA10056//central=apple-smartphone//Wireshark Version 4.0.1 (v4.0.1-0-ge9f3970b1527) sniffer.//
Wireshark is working perfectly on Advertising packets, but...
Our project was previously functional when we were developing using the nrf52840dk_nrf52840 with an overlay to reconfigure for our custom pcba. We created a custom board config...
Hi,
Is the nRF9160 capable of operating on the CBRS band (b48)?
I know it is not listed as a band that is supported by HW but I am curious if there is a software workaround...
Hi Nordic Team,
I am working on the BIS demo, I have three nRF5340 DK audio boards, so I set one as Source, two others as Sink, so is there any resources that when Source...
Hi,
After lots of issues with build and deploy, I eventually have a working version of a BLE App running on a XM122 Radar module. This module have to be packeaged with the...
Hi devzone
there are 2 nrf52 dk board - one is client(ble_app_blinky_c) and the other it peripheral(ble_app_blinky)
and I made it so that if you push the button3 on...
I need to port some functionality that is using nRF5 SDK 17.0.2/ S332 SoftDevice v6.1.1 to an older firmware using nRF5 SDK v12.0.0/Softdevice 332 v2.0.0. It looks like Softdevice...
I'm trying to build the documentation on a Windows 10 system. I've installed all of the required tools and made it to step 4 when I get the following:
C:\ncs\v1.9.1\nrf...
Hello All,
I have a problem when I build my project from sample central_uart & peripheral_uart .
I have two nrf5340 called A and B . B scans the broadcast to A to establish...
