Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
I am working with SPIS on nRF5340. Since my RX and TX buffers will not change, is it possible to call nrfx_spis_buffers_set only once, during initialization? I tried to do...
I am creating the Battery characteristic in a Battery service but I run out of memory (0x04 error) when generating the characteristic. However, that makes no sense. I have...
We’re using Nordic Semiconductor nRF52840 and we may have some problem with RTC when we simulate a brownout. In our application we have both coin cell battery and external...
when I am trying to setup linux with this link https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.6.1/nrf/gs_installing.html#install-the-toolchain
On typing this command...
Hello!
I would like to know the gain of the integrated PCB antenna on the nRF52832 chip. Is there a documentation paper on the antenna itself? I couldnt find any info...
Hi!
I am evaluating DFU over Mesh by following the configuration guide here Configuring and performing DFU over Mesh . I am trying to prepare a package with the application...
Hello.
We are developing using nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral device.
I have a question about setting the UUID. My program has one advertised UUID...
I am using slightly modified master SPI example from here which is running on nRF5340 to communicate with slave device, which is RHD2216 . SPI frequency is NRF_SPIM_FREQ_4M...
Using a nRF52832, I would like to broadcast advertisement packets normally and in extended mode at the same time. Is this possible or do I have to ping-pong between, stop...
ok,i recenlty have gotten iq samples from Rx.but i think my received iq samples are from Tx .i use the NCS 1.9.1 with two boards nrf52833dk.
firstly,i connect antenna array...
Hi, I have already updated all certificates and firmware. But when I am trying to connect my device to the cloud it does not recognize my device. when I am trying to add my...
Hello Dear,
Why the time of uplink state is 950 ms if the data packet size is 0 Byte in mode NB-IoT not in LTE-M?
Can we say that every time a data is sent, it takes 950...
Hello, All
I received following message when I test the code, it appears on both sides,
ASSERTION FAIL [chunk_used(h, c)] @ WEST_TOPDIR/zephyr/lib/os/heap.c :163
unexpected...
Hi,
I have installed Segger Studio for ARM v6.22a.
I have also installed the SDK5 version 12.3.0.
I imported the IAR project project ble_app_start_notification_pca10028_s130...
Hi,
I am after some assistance with creating a 6 layer stackup to use with the NRF52840_CIAA that is 1.6mm thick.
Can you provide recommend layer stack up that have been...
