Good morning,
In my application (SDK v 2.8.0) I would like to disable/enable runtime the advertising for the mesh provisioning. The inizialization of the mesh stack works...
Hi,
Our project need 7 seperate PWM outputs, as the nRF52840 have 4 hardware pwm, I decide to use GPIOTE with PPI to create extra 3 pwm outputs to drive Red/Green/Blue...
Hi, last year the name of the Zephyr module "TraceRecorderSource" was changed to "percepio". In January a PR was accepted that updated the SDK's allow-list (west.yml).
We...
Four returned products after sale could not be turned on & charged normally. Preliminary analysis of disassembly showed that the MCU was damaged, and the MCU was cross-verified...
hi support team,
may i ask do we have demo on how to test remote provision in ncs2.9.0?
i assume there are two possiblilities:
1.
For server, we need add below settings...
Hello,
We are using a BLE module based on nRF52832 with a U.FL connector for external antenna connection. One of our automated tests requires we turn off/on the antenna...
Hi,
I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
hi,
I have used sd_flash_write() in my code. The scenario is that sd_flash_write() will be called after a DISCONNECT event. And it would wait for system events :
NRF_EVT_FLASH_OPERATION_SUCCESS...
Running S120 2.0 central on nRF51422 QFAAE0 (1504CH) and when I call scan_start() i'm getting 0xDEADBEEF at line 431 in file src\ll_lm.m0.c"
Can anybody shed some light on...
IUsing the Master Control Panel application on my Android device to connect to my nRF51822 module (acting as the GATT server), I have implemented the Device Manager (v10 SDK...
Hello all, to optimize the BOM and size of our device(Tag based on nRF51822), the external divider was replaced by software configuration to measure the battery voltage. In...
Hello,
I have seen, that the BLE MAC is increased by one, in dfu_transport_update_start() (dfu_transport_ble.c).
Can someone give me a short explanation, why this is done...
I have successfully compiled BLE application using tutorials provided on nordic website.
but when I start doing debugging for better understanding find out that I can not...
I configured the bootloader to preserve one page of data ( I configured #define DFU_APP_DATA_RESERVED 0x400 on the bootloader project
I also made the same thing with my...
Hey,
We got a problem when trying to figure out how to detect the custom services from Unity. We are trying to read data and afterwards to do some manipulations of objects...
I am trying to implement the following sequence, using SD s130 :
GATTS Queued Writes: Stack handled, one or more attributes require authorization (var #1)
First thing...
I started with programming my nrf52 dev kit board with the soft device (v2.0.0-7) programmed using nRFgo, and then bootloader (from dfu_dual_bank_ble example) programmed using...
setup, I have a 3.3 V battery divided down to the bandgap range using a 56k and 10k resistors, so the voltage at the ADC input is 3.3 * (10/66) = 0.5 V，but the fact is 0.498V...
When I run try to generate code for a simple Blood Pressure profile I get a run time error. I'm using Plugin 1.2 with Studio 1.0.2095. Any ideas on how to fix it?
1:25...
I'm putting out this scenario I don't understand, yet, to see if anyone else might have experienced the same thing.
I have a demo with a central and peripheral that bond...
Best Regards,
while messing around with nRF51822 S130, timeslot API and nRF Master Control Panel, we noticed that:
Issue : if a packet is formatted correctly, but the...
Best Regards,
I am developing a firmware version for nrf51822 based on Softdevice S130 (old v8.1) and Timeslot API.
Currently, I can freely transmit and receive packets...
