Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi I am implementing dfu over modbus. Basically I managed to integrate all the steps (transport, set pending, restart, confirm).
What I'd like to do is to implement image...
Good afternoon,
I have recently purchased a PPK2. I have installed nrfConnect for desktop and Power Profiler on my Ubuntu 22.04 machine. I have connected the PPK2 and...
The example for LZ4 works fine, however I want to use the frame format and not block format.
Therefore I added #include "lz4frame.h" to my main.c and tried to use LZ4F_compressFrame...
My project is developed on nRF52840, it needs to communication with a mobile device through BLE, nRF52840 is as central. The mobile device starts BLE advertising, then, nRF52840...
hello guys, I want to use nrf52840 for my project is it possible to use ST Link for it. because I don't have SEGGER J-link ,if it is possible how can we use it please let...
Hello
I am trying to connect the nRF9160 -DK board to nRFCloud using CoAP protocol. I have written an application for this case. I tested my application with two different...
Hello
I'm trying to connect nrf7002EK with SPI3 with nrf52840DK,
NCS/Samples/WiFi/Shell, but I came up after Flash
The error shown in the image below
I would like...
Hello,
I'm trying to erase/read an external flash ( MX25L6433F) connected to an nrf52840 using nrfjprog. I've created a .toml file for the configuration, see attached. The...
Hello,
With the nRF5340 LE audio application comming with nRF Connect SDK 2.6.0, I found an increase in the audio latency compared to previous versions. I was able to measure...
Hi,
I'm implementing flashing modul, which will be running on external mcu. Therefore for the very 1st step, I have captured traffic while performing dfu on PCA10040 via...
Hello,
Do you have an example that allows you to use the “Service Changed Characteristic” on the server side?
In fact, I saw on the internet that on IOS, we have to use...
Hello,
I am trying to generate encrypted data of particular data with IV and Key value by using mbedtls functions but when I try to do that in AES_CBC example code I am...
Hello,
I have multiple nrf52840 devices ( PCB's ) that act as peripherals and advertise data in BLE 5, and connectable in BLE 4.
We are able to connect to the device using...
I'm trying to enable DFU on our device but am getting a lot of issues.
I used Device Manager to upload app_update.bin and it worked. If I use Flutter example to upload firmware...
