Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
New to nrf52.
Looking for a way to identify radio traffic, to be able to distinguish BLE from 802.15.4 and 802.11. I'm not looking for a full fledged sniffer or looking...
Hi, Nordic Support Team,
I am writing to request your assistance regarding some test failures encountered during the UL certification process for a Matter 1.5.0 product...
Hey,
I am developing an app on a custom board with the nRF9160 which already works in low power. It draws approx. 12uA which is ok for me. Now I need to introduce UART communication...
hi I want to use nrf connect sdk using VS code and i want to start my development on this, now i am unable to install this in my windows 11
1. I have installed this nrf...
Had an interresting issue that we have resolved, but we're trying to understand...
We had a timer (TIMER2) running and matching towards CC[3] every 500us. This match results...
So, I have compiled blinky for the USB dongle52840, but am having difficulty getting west or the development toolchain to flash the dongle. Any help would be appteciated....
I have a custom nrf52833 based board that I tried programming over the integrated JLink on then nrf52 dk via swd. All attempts to program or recover the board failed with...
I was using the PPK2 kit yesterday and I tried the power profiler on nRF Connect (not working with any DUT). I was looking at various apps provied on nRF Connect, I was on...
Hello,
I am developing a project on the nRF54L15 and encountered a system hang when using two UART instances simultaneously: UART20 (for logging and printk ) and UART30...
Hi
I am wondering when I use this function, how much time do I need between I set a TXP and a TXP has been successfully updated. I am developing an application that needs...
I try to set custom compiler flags for the whole project including Zephyr via prj.conf / CONFIG_COMPILER_OPT to compute worst case stack usage as follows: CONFIG_COMPILER_OPT...
Hi all,
I am having difficulties reading microphone data using built-in microphone at Xiao Seeed nRF52840 Sense. I have configured the overlay file as suggested here . Then...
Hello,
I am following the cellular IoT fundamental course with nRF9151-DK.
I didn't have any issue until Lesson 7, but I found that the screen shot of the lesson is...
Hi devzone,
I am starting to write some tests for my application, and I have a couple questions/remarks about the provided Docker image. Link to documentation .
1/ The...
I have done a clean install of the SDK on Debian 13
I have nrfutil install and its working fine - i have tried installing both the v3.2.1 and v3.2.0 toolchains and in both...
