Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi guys. I was observing the PCA10121 PCB layout using this link.
From Murata SWF connector datasheet, it says
https://www.murata.com/-/media/webrenewal/support/library...
Hi,
I am using NCS 2.1.2 with the [email protected] (but I have tested with 2.2.0-rc1 and it doesn't change anything). I have attached a simple example which should just...
Hi team,
I want know how many UART modules on nRF52840 microcontroller? I am confused with one UART and two UARTEs.
Which one is connected to "USB for interface MCU" connector...
Hi,
I have successfully followed the guide for setting up the AWS asset tracker application ( https://nordicsemiconductor.github.io/asset-tracker-cloud-docs/v2.1.x/docs...
Hi all,
I did add a reset switch on my custom board. I read some topics how to active it, but I´m not sure if I did it right.
I did add it in the preprocessor define:...
Hi Nordic,
Soft device is s140
SDK version is: nRF5_SDK_17.1.0_ddde560
Bootloader - Secure bootloader.
We are trying buttonless DFU process using secure bootloader...
Hello,
We are trying to use the nrf91 GNSS with the `nrf_modem_gnss` library. I'm looking for clarification on these fields that are listed in `struct nrf_modem_gnss_agps_data_location...
test setup
the custom board schematic
we tried to flash the custom board with the beacon sample here https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr...
I just upacked my new nRF52 DK and installed what I think are all the goodies to do development (on my Windows 11 laptop). I can see the board with the Programmer and I loaded...
Hi
I am using 4 x AD7410 in each TWI channel, using both TWI ports. So, altogether 8 AD7410s. ( I used the Adafruit breakout boards).
Initially I get the temperature readings...
The BOOT_SERIAL_WAIT_FOR_DFU feature is meant to wait a number of milliseconds (500 by default) for a message via serial comms. If it doesn't receive a message it continues...
Hello,
I have following problem:
I am using a multilink NUS Central. With one peripheral connection everything works fine. But when make a second connection I sometimes...
Dear support
Try to perform DFU OTA on my final target board and have an error state says - "payload(250 bytes) too long for MTU: 249 "during uploading stage, could anyone...
Hi,
I am developing application on NRF52840 with Zepyr 2.1.2 SDK, and I found two problems when using the example scan_adv, as follows:
Executing bt_le_scan_start in...
My team is developing for an nrf52840 on a custom design pre-production PCBA. Up till now we have been using nrf52840dk_nrf52840 in the"Board" field of the "Add Build Configuration...
