I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
-
Is it better as the ATT MTU size is larger?
I am trying to do nus communication between nrf board 1 and board 2. The data size I want to send is about 30 bytes. Previously...
To make sure that the nRF52840 SoC is not powered when the nRF power switch (SW8) is OFF.
So what happens if I power the nRF52840 SoC when the nRF switch (SW8) is ON ?
Hi ,
When i run samples/keys/hw_unique_key app and select nrf9160dk_nrf9160_ns board . The app can not run into main function instead run into system_halt.
__WEAK...
Please provide the part number(s) of low-cost NORDIC processors that have a quadrature decoder and a PWM.
We are working on an application that is using a Nordic nRF52840...
Hi,
During the validation of our device, we found that the RTC (synthesized from HFCLK) was quite a bit off. Instead of the expected 32.768kHz, we measured 33.047kHz.
...
Hi, I am using urf52832 ( also have 52833 dk).
I am trying to use another pin us uart, which tx is 29 rx is 30 define in project_pinconfig.h.
But I can't see any uart...
Hello, I'm working with BLE Mesh using NRF52840
- Our setup: NRF-Connect-SDK 2.1.0
- Summary of our project.
+ Provisioner node to control lightness for all nodes in...
Hi,
I'm having an issue including USB DFU Trigger library in my prototype application running on nRF52833.
My application is based on the ble_uart example, to which I...
Hi,
My application is written on top of freertos ble example. I need to integrate radio test example as well for certification. I am running into errors when I try to...
Hello,
my first Post here, so i hope i do it correctly.
I have the following Problem with the Configuration and Communication over TWI/I2C.
The Voltage of the TWI...
I am working on BLE on NRF52840 using soft devices for BLE and I was using sd_ble_gap_ppcp_set API to set the connections parameters for the BLE so I think the PPCP is the...
I'm calling this function from a Zepyhr project:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/connectivity/bluetooth/api/gap.html#group__bt__gap_1gad2e3caef88d52d720e8e4d21df767b02...
