Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm trying to config my SAM-M8Q with an array of HEX.
It's work beautifully with app_uart_put like the picture below.
However, when I try to implement LIBUARTE...
Hii
I have a problem pass the address while advertising
I should pass the adress using 9160_dk
However, in main.c there is this line:
#define DEVICE_NAME "Nordic_UART...
Hi there, I'm trying to find a hardware integration guide that details min max specs for the IC and also details the RF output pin impedance so I can match to my board stackup...
I checked out the nrf github repo and tried to build the nrf_dm sample for the nRF 52840 dev kit which is what I have
In VSCode I chose "Add an existing application" and...
Hi,
As the title, I can see Mesh Proxy service in nRF connect app, after provisioined device by nrf Mesh app. But when I send data to Mesh Proxy Data In, It disconnect immediately...
I followed the document and downloaded nRF Connect for Desktop in Ubuntu 18.04.5.
Then I changed the permission of nrfconnect-3.11.1-x86_64.appimage to "allow executing...
Hi,
We have an issue that is puzzling us.
The symtoms are the following.
If we flash v1 of our application (using Segger Link) to our target, it works correctly, no...
Hello,
I am experiencing a power issue after the first ADC sample is triggered. Sampling 2 ADC channels using PPI and TIMER as the triggering mechanism. Here is a capture...
nRF SDK 17.1.0 sd140 7.2.0
I'm working on adding OTA DFU to ble_app_uart. I had my own custom service that was working and then added on the DFU files like ble_dfu.c and...
Hi,
This question was asked before here a year ago, but I couldn't really find a definitive answer in the thread
Is there any reason why I would not be able, technically...
SDK V17.1, nRF52840 SOC, s140_nrf52_7.2.0_softdevice.hex
I am attempting to configure a spi device from a ble gap disconnect event handler. Before the disconnect event communication...
Hello,
I have tried to find examples where I can use nRF52820 chips for Thread applications and I can't. Program memory is too small for any application as far as I've searched...
Dear,
- nRF connect SDK 1.9.1
- nRF5340 DK
Here is my code and config. I can assign some pin as gpio such as 0.04. Maybe 0.03 or 0.13 have other function mux, but I...
I was trying to build my own devkit based on nrf9160 and I wanted to which hardware to use to upload code to the nrf9160 chipset.
I tried getting the chips used on nrf9160...
Hi,
I am having a trouble to flash Nordic Thingy 91 on My PC.
I have followed the instruction as bellow.
https://www.nordicsemi.com/Products/Development-software...
