Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
I want to enable GPIO IRQ in Trusted firmware-m 1.3 on nrf5340DK. I have TFM 1.3 which comes with zephyr v2.7.0 image flashed to board. followed the steps of https://www.trustedfirmware...
Hello,
I am trying to protect the battery on our application by putting my device in DEEP_SLEEP_! mode when a certain voltage is reached and waking it up upon a GPIO input...
Hello, i would like to know if this is possible to send less than 20bytes per packets, by changing the parameters like BLE_GATT_ATT_MTU_DEFAULT or the max data len. My goal...
Hello,
I'm trying to evaluate the Thingy:91 on Nb-IoT networks. I'm currently in the Philadelphia suburbs. I'm using the iBasis SIM card which was packaged with the device...
We like to use nrf9160 and we tried to find operator in India who sells NB-IoT / LTE-M sim card. but unable to find. Is there any operator providing NB-IoT / LTE-M enabled...
Dear Forum,
Im using a NRF52840dk connected to a NRF9160dk with the SLM application running.
Sending uart data from the 52840 to the modem works and modem gives a response...
Greetings to my fellow NDZ colleagues, We have developed an ecosystem of devices which operate in a sensor network in BT Mesh. We are using nRF52840 and our code-base is nRF5...
Please inquire about NRF 24L01+ RF TEST tool.
I am going to proceed with the KC certification wireless test.
Can I get support for the NRF2401+ RF TEST Tool and procedure...
Hello
I have success to load and run the sample, but....
After receiving OK from the AT#SOCKET=1,1,0\r\n command I could not success to AT#XCONNECT="google.cm",80\r\n...
Hi,
I am developing a device that uses a custom nRF52840 module. This module is assembled on a mainboard that contains an ICS-43432.
We are developing the firmware using...
Hi all,
I'm recently working with Nordic devices (more precisely nRF52840), so I'm still learning. I'm working on a project where I have a shared SPI bus with several devices...
sorry i closed the problem by error
Hello, I did my own custom board with an nrf52805 and I'm trying to put a module with different frames, and when I do that my...
Dear DevZone Team
The nRF9160 datasheet stipulates output power as +23 dBm. I read this as conducted output power at ANT pin and not EIRP which to my knowledge implies the...
