When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
It's a coding question. Maybe it has nothing to do with NRF.
I'm playing the central example hrs. I have a custom .c file that wants to access the m_hrs_c variable defined...
Hi,
We are developing a system with nRF52840 chip and we have to feed the soft device (s140) hex file & our application hex file into custom board which we are developing...
hi,
For NRF52840, is the 125kbps sensitivity the same as on Radio? I used the 125kbps long distance mode, but the distance was not up to the ideal state, the deviation was...
Good morning,
I'm developing an application for nRF52805.
I saw that in SDKFolder/config there are all "complete" sdk_config.h files for all nrf52 targets except for the...
Hi,
I am using own hardware board based on https://www.raytac.com/product/ins.php?index_id=24 module, it uses nRF52840.
I
I am facing an strange issue that UART is not...
Hi,
can anyone provide any insight into moving beyond a pca10040 development board and creating a project for a custom board? What are the steps that you have to go through...
Hi,
We are looking to be able to reflash our devices on the field, as well as do FOTA. Critical device information (serial number, encryption keys, etc) are stored in the...
How does the ADC gain block work.
Suppose using Vdd=3.3V as ADC reference, analog signal input from 0 to 3V and gain 1/4
What will be the ADC core voltage for single...
I have an application where i have to regularly send gps data to an mqtt broker. I started with the mqtt sample which works fine, and i also tried the gps example with assited...
Hello,
I am trying to extract audio from the thingy's microphone using the microphone driver. I know that the data it produces is encoded in dvi_adpcm. I would like to decode...
Hi,
I am using nrf52833 development kit and using nRF5 17.2 SDK on KEIL IDE with softdevice as S140.
I am trying to compile ble_app_template example from the peripheral...
Hi Iam using NCS version 1.5.0 and DK version 0.15.0
Is it even possible to perform FOTA over SMP BT on NRF9160?I am using 840 as my controller and normal ble functionalities...
Hi,
I'm developing a system where I have a two button "remote" and connecting to movable part that plays sounds. My plan was to have a nRF52 in each of the parts. So ...
1. Can nrf9160dk protect code avoid any one to read firmware out and copy them in usb 2. Can nrf9160dk protect code avoid any one to read firmware out and copy them in externl...
Hi All,
I have 2 boards nrf52840 pc10056 and I need to run ble_app_uart using LIBUARTE with DMA in order to obtain a more robust uart communication
I would like to use...
