I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
NRF Connect extensions running within a flatpak VS Code on Ubuntu 25.10.
First of all, fixed the certificate not found issue that some folks have reported in other questions...
Is there a workflow white paper on how e-sim is used or is there documentation in the example workspace? If it's the latter is it easy to point this out? Thank yo.
Environment
I can see a Usage fault on MPSL Work with invalid PC ; addr2line shows Zephyr frames for some LRs and no symbol for an address in the SoftDevice/MPSL range....
Hi,
we are trying to get the psa attestation on the nrf54l15 to work. We have tried config options for hours but CONFIG_TFM_PARTITION_INITIAL_ATTESTATION always gets 'n...
In the NCS SDK, is it possible to implement periodic broadcasting of a certain number of data packets, for example, quickly broadcasting 3 data packets, then waiting for 10...
Hi everyone, I have a central firmware application connected to 2 peripheral devices: A and B.
I use the method bt_gatt_write_without_response_cb (from zephyr>subsys>bluetooth...
I measured the impedance using a VNA on the J1 socket of the nRF54L15-DK RF: With the RF configured for receive at 78.6 + J7.8, RF transmit continuous carrier at -40dBm: 23...
Hi,
I’m using GD25WB256 as external flash on nRF9151 for MCUboot secondary slot. It’s currently not available from our supplier, so I’m looking for alternatives.
Current...
Hi Nordic support:
Our product used nRF9151 modem. During production, we encountered an issue with approximately 0.1% probability on the nRF9151: It's firmware lost or corruption...
I used the timeslot function of the nrf52832, but when I called the radio to send data, I found that the signal strength was very weak, much lower than that of BLE. This resulted...
I am using nRF9160 DK with nRF Connect SDK v2.9 and the LwM2M client sample ( /samples/cellular/lwm2m_client/ ) , converted from PSK to X.509 certificates .
The device connects...
In the software development for the nRF52832, the SEGGER_RTT_printf() function is called throughout the code for debugging and problem analysis.
Would there be any particular...
Can I copy the ESB code from SDK v3.3.0-preview3 into SDK v2.9.0, and then get the functionality in esb_ptx_ble & esb_prx_ble?
Is there any way to achieve it quickly?
Hi,
I am working on a project with two nRF52840 devices (nRF Connect SDK 3.2.4 / Zephyr RTOS) that are already connected via BLE. On top of the BLE link I need a low-latency...
