Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Dear Nordic,
I have a BLE mesh product that is in pre-production. The mesh gateway is composed of an nRF9160 and nRF52840 with a UART link connecting them. The nRF52840...
Hi,
I have updated nRF Mesh to 3.1.0 version (iOS), but I can not see any field for reading sensor values. I set app key and publish/subscribe addresses for sensor server...
Disclosure. I am new to firmware develoment. My experience is in cloud development.
I just bought a Thingy91. I registered online using nRF Cloud. The modem communicates...
I want to use a timer to get a fixed time interval, so I use a 32-bit timer to count from 0 to 10000, and use PPI to clear the counter when it is captured to 10000, such as...
I'm using Softdevice S132 V 7.0.2 with nrf52832 module. Project is in Segger Studio. Project runs in debug configuration as in debug or in non-debug mode. When changing to...
Hi, I want to run hci_usb as a USB dongle, and use the CONFIG_BT_LL_SW_SPLIT software based link layer controller on nrf52840dk
But somehow once config as CONFIG_BT_LL_SW_SPLIT...
nrf_ble_ancs_c.h has hardcoded max attribute length of 32 (BLE_ANCS_ATTR_DATA_MAX).
1) BLE_ANCS_ATTR_DATA_MAX mainly seems to be used to allocate the size of the app_id...
I'm working on an nRF5340 based design and using the nRF5240DK to get started.
I would like to have an immutable first stage boot loader, an updatable MCUBoot boot loader...
Are there any suggestions for creating slightly customized versions of the immutable and MCUBoot boot loaders?
Currently I'm using CONFIG_SECURE_BOOT=y & CONFIG_BOOTLOADER_MCUBOOT...
I would like to include the MCUBoot library code into my application so that I can read and validate update images (before restarting the MCU to install them via MCUBoot)...
I have a custom MCUboot boot loader working. Now I'm trying to build an application to be updated by MCUboot. I've added the following to prj.conf:
CONFIG_BOOTLOADER_MCUBOOT...
I am running a NUS at 115200 Baud and it works fine but when I run it at 921600 my BMD 300 triggers a Serial Fault. Is there a trick to get the 921600 to work without flow...
Hi Guys,
I need to connect to a BLE device using NRF52480 using passcode (6 digit pincode)
on Android it works just fine, I attempt to connect and displays the popup...
led 1 is off but p0.13 get 3v output , similarly led 1 is on p0.13 get 0v output, how to change it help me. similar for led 1 to led 4 respectively p0.13 to p0.16.
Hi I am the user of zephyr and nrf connect SDK in ubuntu 20.04. one question about file path in the header file. for instance, the demonstration "nrf/samples/zigbee/light_switch...
