I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
Hello,
How can I directly read out the POFCON register value on the Watch Window while debugging?
Where is it actually located in the library(sdk 14.2) source code?...
How can i know how much time the microcontroller spends in the timer_event_handler() function? I am fear that i have written down to much code into that function. Regards
Hello,
I have the following statement in flash_placement.xml:
<ProgramSection alignment="4" keep="Yes" load="Yes" name=".nrf_queue" inputsections="*(.nrf_queue*)" address_symbol...
Hello.
I have two nRF52832 (central and peripheral). Connect the central and peripheral and call sd_ble_gap_rssi_get() on the central to get the RSSI and channel. The attached...
Hello there!
At this stage of the product development cycle, we would like to be able just to take simple reading from ADP536x module (to read either battery percentage...
Hey all,
For new minor revisions (1.X.0), will they eventually be supported by telecom's that are currently running with lesser versions? For instance, the current modem...
Hi,
I am using nrf52832 with icm20948 (I2C) on custom board and I am using icm20948 for angle measurement. For custom application I added some features i.e, before reading...
Hi,
We have preloaded the module test board with the DTM test from NRF5_SDK16.
The lab is requesting for the driver to pull up the testing interface and instructions...
I am exploring nRF52833 in a project using DK and Keil IDE. However, I keep getting errors when I attempt to download DeviceFamilyPack, etc. This error only occurs if I try...
Hi,I have a problem.I used three channels of ADC sampling in the project.If I connect the ADC port directly to GND,the ADC value of the sample is not equal to 0.But if I change...
hai ,
In my application , my nrf52840 device in peripheral mode to connect with central (ESP32).
then if i get a mac id from central ,i need to connect over with central...
Hello,
For my project I use uVision v.5.23.0.0; now I am willing to prepare two different targets using the same source files: one target for debug, with included the drivers...
Hi,
I am using nRF5_SDK_15.2.0_9412b96 SDK and dev board - PCA10056 V1.1.0 2019.22 - 683524107
USB serial driver is not detected on Windows 8.1 Pro while testing my customized...
