Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hello I working for TSS.se now selling 100.000 temperature-loggers annually. We aim to develop a new IoT based logger based on nRF52832 as a replacement.
We have developed...
I am trying to use a Raspberry Pi B+ as Bluetooth to Wifi bridge. But I find that the bluetooth range is very diminished when talking to my Nordic nRF51 and nRF52 devices...
Sir,
I have a question about the connection's power setting of the BLE.
I use the API as the screenshot, but there have a error return. I don't konw the reason, so I...
I am following Getting Started Assistant on Mac platform.
However, I run into an error when I issue: " pip3 install --user -r zephyr/scripts/requirements.txt ".
" ERROR...
Hello,
there’s a section in the NRF9160 specification (11.1) that calls out that VDD_GPIO should be applied after VDD has been applied on power up and VDD_GPIO should be...
Hi,
I am sending firmware image using my DFU master. The image needs to be divided into data objects each of 4096 bytes and then those again into 244 byte BLE packets. So...
Hello,
I'm trying to connect to nrf connect with the nrf9160 DK. I am using an Irish vodafone NB-IOT sim to establish the connection. This sim has an access control list...
Hi,
I have a question regarding a DFU update via BLE. I am using mesh sdk v3.20 and sdk v15.30 with custom hardware (nrf52840).
I have the BLE DFU working as expected...
Hi all,
I am using mesh sdk3.20 and sdk15.30.
I noticed that with the buttonless ble dfu, it is not possible to perform a DFU transfer after the device was provisioned...
I did the program using examples of glucose. But I do not want to enter passkey from central. Because there is no LCD or UART in my device. Which part of the glucose example...
I am developing firmware for my Peripheral Device (nRF52840) using S140 (v7) and SDK 15.3. In my application, I will advertise (with advert payload changes) and support Smartphone...
Hi,
How much is the expected time period from the time VDD goes above 1.75V to main()? I am using a custom bootloader and am seeing a ~4.5s (yes seconds!) delay in getting...
i'm trying to configure the nrf to rx and according to the state diagram i realized that: as the nrf is supplied and the voltage goes over 1,9V the nrf goes in the power down...
Hi, i'm using the nrf24l01 with a zynq board to use it as radiocontrol; i'm trying to configure the nrf as receiver so that i'm able to send data from another nrf connected...
Hi, i'm using the nrf24l01 with a zynq board to use it as radiocontrol; i'm trying to configure the nrf as receiver so that i'm able to send data from another nrf connected...
