Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm experiencing high packet loss with the application nrf5340_audio example, I'm using nrf5340 audio DK as a unicast server, and then I'm using a Sony phone to connect...
Hello, I am using nRF52832, nRF5 SDK, s132, and DFU-OTA with private keys and secure bootloader I am trying to enable the DFU Downgrade by disabling the define NRF_DFU_APP_DOWNGRADE_PREVENTION...
SDK:11.0 Example:ble_app_hrs\pca10040\ s132_with_dfu
Hi Does nrf52810 only support a maximum of one central connection at the same time? If I currently want to connect two...
We wanted to understand better the use of external NOR Flash for nRF9161 applications. For example, in nRF9161-DK, this would be the GD25WB256E chip.
For modem delta fw...
Hi!
I just succesfully flashed my modem firmware to version 1.3.6 using the nrf programmer and a segger external programmer. I can still connect over the serial monitor...
I used nRF52840 board with SDK 17_1_0 ,
I want to used WS2812B in my project so any one can give me reference code for this or
can suggest me how can i implement its driver...
Hi,
I am using nrf52840 and SDK-16.0. Initially I was using SPI1 and SPI2. now along with this I am using SPI3.
we have added new feature which consumes 316*9*26 bytes...
I am trying to cancel a pending connection as a workaround for .
However when I run:
```
LOG_DBG ( "Peripheral connection timeout cancelling and trying later" ) ;...
Hello . I saw this issue raised previously but with no resolution so here it is again
I built the smp-svr sample in VSCode with Zephyr SDK 2.6.1 which produced a DFU package...
Hi all,
The question is about 125kbits and 500kbits long range modulation in proprietary protocol. I'v seen a post saying that is technically possible ( ).
But is...
Hello,
I have a project in progress with an NRF52840 chip. I was able to buy an aircard with the same chip www.kickstarter.com/.../aircard-find-your-wallet-always With this...
I receive the following error message when trying to install the toolchain manager (V 1.5.0) from nrf connect for desktop (V5.0.0):
Error: Failed with exit code 1. Failed...
I've been experimenting with the nRF5340's HFCLKAUDIO clock, and have discovered a discrepancy that I cannot reconcile. Table 23 in the datasheet details the peripheral's...
Hi everyone, I am trying to send data over USB port for the nrf7002 dk Could anyone have any guide, tutorial, resources, or suggestion on how I should do that project config...