Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
hi ,
i am trying to make a project based on detection using ble 5 on raspberry pi 3.
plz help me with selecting correct and most appropriate ble 5 dongle for good range...
Hello, Dear Support. I try to build BLE Mesh from several nRF52840 Development Kits. I use example [serial] from SDK for Mesh v3.1.0. After building solution in SeS and starting...
Hello:
I am able to compile, load/flash successfully for my BLE + FreeRTOS application to my nRF52840 DK board. However, I am not able to start or pause execution of the...
Hello.
I am trying to migrate from sdk 11 to sdk 12 and I am having difficulty in adapting the device_manager.h functions that I am using in my code to the peer_manager...
Hi
I would like to be able to (force) stop characteristic notifications at some point in time.
Imagine a smartphone connects to peripheral and enables characteristic notification...
Hello,
I wanted to test the range of long range bluetooth using two nRF52840 USB dongles with the blinky example firmware of the nordic SDK 15.3 combined with softdevice...
Hello,
I am using nRF52832 DK PCA10040 v1.2.4, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I have very basic query...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
RESETREAS will give cause of reset. But for...
Dear Team
I use the Lwip_mqtt_publisher example from the SDK 15.3 with a PCA10056 board.
Also, I used an Ubuntu 18 Instance(IPv4, I used 6tunnel) to run the Mosquitto...
Hello sir ,
I have conneccted an BLE400 dev kit to an swc J-flash device. And i can't erase it.
Tried with nRFgo Studio on windows 10 an with linux nrf cmd line...
Hello,
I am using the chip nrf52840. I am trying to configure three pins (P0.09, P0.10 and P0.11) as output pins and I am trying to make set and reset functions for them...
Hi ,
I am using NRF52832 ,SDK15 my code is based on the HR_FreeRtos project , I am using the nrfx_wdt API to implement WDT in my code .
I am using a LDO for the voltage...
I'm developing a product that use the Nordic UART service over BLE and need something similar to a USB serial port, except with NUS. Is there a Windows 10 driver that works...
