Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Greetings. Is there a way to do information mapping using, for instance, one of the mesh nodes that could act as a client/provisioner to all other nodes and therefore keep...
Hi! I'm working with nRF52 development kit and SEGGER Embedded Studio. I was trying to modify the example given as ble_app_hids_mouse and take all the functions present in...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I have few queries on System OFF mode.
1...
Hi, i am trying to add additional payload to the Mesh Light Switch example. However, i modified all structs and it came down to the status_handle() function inside generic_onoff_client...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
After wakeup from System OFF (due to GPIO event), I want to validate / debounce...
On the nrfCloud, when you clicked on a device (nrf9160DK), the previous version of the interface would show how much data was used of the "available" data associated with...
We are developing a cycling application and are currently using a variety of ARM processors with BLE capability. We require to add ANT+ capability to read Hear Rate monitor...
Hello,
I'm developping an android application for detecting falls.
I will use accelerometer's values for find the g constant.
But i recover bad values.
this is my...
Without doubt there is a new variation of software emerging:
We are all familiar with Firmware and Software, however I really feel the need to coin the term "Whisper Ware...
I am experiencing a problem where behaviour after an sd_nvic_SystemReset() differs from behaviour after a power-on reset, and this difference causes failures in the softdevice...
Hi, I see there are several questions related to using GPS pulse per second signals for synchronization between devices, but I can't see the responses to some of the questions...
Hi,
I am using Uart1 on nrf52840. This is implemented using nrf_serial library. I have set buffer size to say 10, so event occurs on every 10 bytes reception. Now I want...
Hi,
I have been looking at the Nordic examples and I found them to be pretty slow with the handlers being the bottleneck as opposed to the actual hardware. I was wondering...
I'm developing an application to support multiple concurrent central-and-peripheral connections. It's a bit messy but is just about working. At the moment I'm using SDK 9...
Hello All,
I am facing problem in compiling uECC.c on windows10.
Please any one tell me what is the procedure to build and compile that file.
I have tried on the compiler...
