Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
What is the difference between the twi_sensor example and the twi_master_using_app_twi example? Where do I find any documentation that describes the available functions for...
Hi
we are currently designing a device using the nRF52840 and are looking for information on the most cost effective way to do large scale production testing.
will we...
Hi,
I have an issue with pinging the nrf52 (PCA10040)(with mqtt_pub loaded), from the PC on the LAN to which the Raspberry Pi is connected to.
I can ping the nrf52 from...
Hi, I've followed the tutorial on https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-services-a-beginners-tutorial . I got to the end of the tutorial...
Hi,
In your reference design: https://www.nordicsemi.com/DocLib/Content/Product_Spec/nRF52840/latest/ref_circuitry?1070#unique_1780233596
There is a line from DEC2 to...
When I debug my product ,using nrf51822, using the ble_uart example, my product will using MCU commnication with BLE,using uart.
When I modify the PIN of the uart TX pin...
Hello:
I am working with my sales contact at AT&T in the USA. I mentioned this module and that it was going through certification. Before I moved forward with the carrier...
Hi,
I'm using an nRF52840 dongle with pc-ble-driver on Linux. It has connectivity 6.0.0 with S140. I tried the heart rate collector/monitor example pair (I have two dongles...
Hi folks,
We are in the process of evaluating nordic chips for our product.
One of the features we need is the ability to record an audio sound from an Ios app, send it...
Hello,
I have got nrf Power Profiler Kit for power consumption testing in our application board. I have a question regarding its output voltage for DUT devices. My application...
The project I am working on is to store the data acquired through BLE_uart_c and the data collected by the sensor on SDCard. I use FreeRTOS. The problem is described as follows...
Hello,
I have been developing a project and have run into an issue that I have been unable to resolve in the past two days. The code I have is in every way similar to other...
Hello,
I am using multiple custom boards with ISP1507-AX modules from InsightSIP, based on the nRF52 chip. I want to verify the revision numbers of the nrf52 chips inside...
Hi,
When libubsan and libasan is install the build systems enables some sanitize features in the compiler. These are trigger by the unit tests and four of them fail.
The...
Hi there!
It seems like I've accidentally destroyed LTE modem firmware in my nrf9160 DK during some experiments.
DFU update utility just can't flash the latest firmware...
