I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
Hi,
I am implementing modified DFU for nRF52832 which uses external flash memory. If power loss occures during update process, device then start update process from the...
Hello sir,
I am working on my final PCB design using nRF52832 chip. As per your reference Bill of material i use same part number for all components recommended by you. But...
I have a custom board with the nRF51822 QFAA . Schematic:
In order to compile the firmware, I'm using MinGW . As you can see, I'm also using the SDK 12.3.0 .
Finally...
Hi,
I am using nRF52832 and softdevice is S132 adk13.1. My application is read 3 ADC channel one by one and send this value to android app using NUS. For this i have use...
Hi,
We are performing data transfer using NUS service (BLE-UART).
Data passed is a 11-character string.
READ and NOTIFY permissions are provided for Tx characteristic...
Hello,
I am designing NRF52832 based board. I followed the exact reference layout suggested by Nordic except via position. I moved few vias during routing. Is it necessary...
I am using segger studio and jlink to program my nordic thingy 52. I followed the documentation and
Build the program
Connect to Jlink
Erase All
Debug->Go ...
Hi!
nRF52. S132, SDK13.
I try to use ble_dfu_send_hex example.
what shoul I do first?
via nrf gostudio load SD. correct?
Which SD? from this folder (dfu_test_softdevice_s132...
I get the mesh SDK here: http://www.nordicsemi.com/eng/Products/Bluetooth-low-energy/nRF5-SDK-for-Mesh/(language)/eng-GB
But I don't know how to add pwm to the light_switch...
Hi all,
I use the nrfjprog 9.7.1 and unfortunately I was used the --rbp command on my nRF52832 and now it's impossible to execute --recover command.
The nrfjprog log shows...
Hi,i have some problems when develop with experimental_ble_app_buttonless_dfu project in sdk12.3 on IDE embedded studio (MAC OS).
I follow this link text to develop.when...
Hello,
Some problems I meet when I try to use spi manager in ble_template example to read "who_am_i" register of LIS2DH12. The environment is set as below:
nRF52832...
Hi,
I'm using SDK13.0.0 and softdevice S132 v.4.0.2.
I sometimes get NRF_ERROR_INVALID_STATE from sd_xxx() in the function registered to ble_evt_dispatch() when connection...
Hello,
I would like to establish communication between my pca10040 and my cellular modem.
Currently I am using ble_app_uart on the peripheral example and I can put messages...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
