Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hi,
I am developing a product for the 433MHz band. Due to the space constraints I had cut the ground plane to very small and also had to rearrange the components away from...
Hello everyone,
This image was copy from "infocenter.nordicsemi.com".
I'm trying nRF51-DK (IoT SDK) with Coap server , (raspberry pi with Coap client by python example...
Hi,
we are using RTC2 with APP_IRQ_PRIORITY_LOWEST. But the code hanged inside the interrupt handler. when we did step through debug, we came to know that in nrf_drv_common...
In nrf52_SDK/examples/peripherals/rtc we tried adding the UART prints and verified. It was working fine for RTC0 but fails to do for RTC1. Could you please give any hint on...
Hello together..
i have a problem with the nRF51 DK.
I tried a little bit with this DEVkit i.e. copy the blinky example to the JLINK storage.
This works fine.
Regarding...
Hello,
I am developing a new product using S130 on nRF51822(QFAC). My product use LCD as spi interface and ADXL345 sensor as i2c interface, also test it, works well without...
Hi all:
To saving power I implement the function to read data after interrupt is triggered..
below are my codes..
My expectation is..
Let CPU enter idle mode to wait...
I am trying to set up a GPIO interrupt, and found that whenever Button 1 is pressed, if Button 1 or 2 is pressed later, the app will reset. This is even if there is any other...
Hi.
I want to make a device which can connect each others and communicate with NUS.
I need not to use any other service without NUS.
I made nus_c service which is a central...
Hi
I can't seem to find this in the datasheets, what is the active current consumption of the nRF52832 chip, I'm interested in the maximum expected current consumption...
Hi!
I want to connect a nrf51 dk with a beacon and I'm using the UUID to make the connection. In the beacon code I define the UUID in this way:
ble_uuid_t adv_uuids...
I use nrf52832 with softdevice s132_nrf52_1.0.0-3.alpha for a ble application on own pcb.
first I'm not sur of adresse to use for iROM and iRAM areas. I've this parameters...
//Hi Everyone!
//I am programming a nRF52832 through the SDW interface and am having trouble answering some questions.
//So, first off is simply checking my understanding...
I have a recent dev board and am using SDK11 with gcc.
I can build and flash OK
The blinky sketch runs
However, when I load up examples/ble_peripheral/ble_app_proximity...
We bought the Beacon Kit from Nordic. I'm trying to use the firmware code on a similiar beacon board based on same Nordic Nrf51822. The board has same button and led pins...
