I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
Hi,
I'm unable to run any application on nrf51 DK (Keil used). When I start debug (no matter what application I load), program always cycles between 2 instructions:
0x000006CC...
Hi,
My application uses the softdevice 110.
Everytime, there is an event on my sensor. The sensor sends the event to my pin, which generates a gpiote interrupt . But, the...
Hi,
I'm trying to determine why a HCI DFU upload fails.
There is a log of the communication below showing the serial request/responses on the Windows side.
Is anyone...
Hi: I use dfu_single_bank_hci to update application. HCI_SLIP_UART_MODE = APP_UART_FLOW_CONTROL_DISABLED, HCI_SLIP_UART_BAUDRATE = 38400.
I use command " E:\hci_dfu_send_hex...
Hello,
In my quest of working with pstorage_raw.c I found an annoying situation when I tried to clear small portions (as I thought by using raw I would have full control...
Hello!
I have based myself on the ble_app_uart example, taken out the UART bit, and all that remains is the bluetooth functionality.
I have also implemented SPI communication...
hi guys, :)
I used SDK 6.1.0., Softdevice version is S110_nRF51822_7.0.0.
I compiled the template project. (in the "C:\Keil_v5\ARM\Device\Nordic\nrf51822\Board\nrf6310...
I want to use the UART to get and send data to another MCU on ble_app_beacon of SDK 8.1.0.
But after I add the UART function to the project, the UART can't work.
Can the...
Thanks for the SDK 8.1.1 fix. Please make it available also as a .zip in developer.nordicsemi.com/.../
Currently the fix cannot be used with a GCC toolchain as it is only...
Hi,my friend
I use the nrf905,At one end Use the PCB antenna, on the outside part of the metal.Using the results, said communication distance is shorter than 40 meters, easy...
Hi,my friend,
I have been using nrf905, but its performance is very bad.
Have a compatible chip nrf905 data communications? Working frequency 433 MHZ,100 KBPS baud rate...
uart_fsm and proc_fsm never get called.
debug on the first line of the uart_fsm and proc_fsm are do not come even
gpio toggling stops once uart interrupt received. I am...
Hi there,
I'm trying to build the Beacon source code with GCC toolchain on Ubuntu, but it's not working on Beacon Kit, there is no any response from the kit. But I tried...
