Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I’m developing a product that uses the nRF9160 for LTE-M and the nRF52840 for Bluetooth. The nRF52840 is a pre-certified module, and I have experience with FCC compliance...
Is there any hardware limitations that would prevent one from using the nrf_802154 drivers on an nRF9161? If no, could you adapt the open-source sl to use the 9161 modem instead...
Setup: custom nrf9161 PCB, flashed with nrf9161 modem fw 2.0.1, using NCS 2.6.1
Targeting my custom board, I couldn't even speak to the modem lib, no IMEI etc.
So I dug...
Hello,
I have been trying to correctly setup my nRF Connect inside VS Code.
When I try to execute the command
west -V
in a nRF Connect window inside VS Code, I...
Hi i am using nRF52840 with segger embedded studio.
SDK -> nrf5-sdk 17.1.0 I want to configure rtc2 so that whenver i initialize it it should generate an interrupt after...
Hello, I am building a device which simultaneously advertises as a beacon and acts as a peripheral role device. Advertisements are sent at ~20 Hz with the connection to the...
hi:
I am use broadcast_sink and broadcast_source of nrf5340_audio simultaneously. use a button to switch source or sink. i am use NCS v2.6.2 if switch to sink mode is show...
Hello friends, I am using nrf52833 MCU for my current project, this project involves a sensor from infineon that operate on SPI and it supports high frequencies up to 50 MHz...
Hi,
I referred to the DevAcademy FOTA over Bluetooth Low Energy, but in the provided code, the BLE mobile app connects to the device and it automatically enters DFU mode...
on cannot connect to the on-board Jink of the NRF52840DK board
I have tried:
Updating to the latest Jink driver
installed nrf connect tools for windows
connecting...
Hello,
I'd like to develop a BLE OTA Bootloader using the NRF Connect SDK, but I need to program my NRF52840 with a Serial Wire debugger. What tools do I need? Is there...
Hey,
Im have a thingy91 and multiple nrf52840 pcbs.
my goal is to make the thing91 a central device that reads data from the nrf52 devices and sends it over to the cloud...
We have a custom board with an nRF7002 controlled by a non-Nordic MCU. The WiFi drivers were ported from SDK 2.7.0, and WiFi in general is working, this question is about...
(I am a beginner) Hello, I recently got the Nordic nRF52840 dongle so I can sniff BLE packets from some devices I have. I set up the dongle following the recommended setup...
Hi,
What is the voltage on nRF52811-CAA chip DCC pin (A5)?
Can the regulated voltage on this pin be used as a voltage source to supply some external circuits?
Please...
