I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Using the nRF52840 with NCS v2.6.1, I want to put the device into a low-power sleep state during idle time. Before sleeping, I configured a GPIO interrupt as the wake-up source...
Hi everyone. I'm trying to read data from an MS5611 pressure sensor using the nRF52840,
but the I2C communication isn't working.
Upon checking, I noticed that the I2C...
I have a board with an nRF9151 device on it that was provisioned to the nRF Cloud under one User Account.
I would like that device to be in a different User Account, and...
Hi,
I'm using nRF connect extension with VSCode and developing for Actinius Icarus IoT board (which uses nRF9160).
Even when building the example code of hello_world ...
I tried generating sec_tag using sys_rand32_get() or other arithmetic method during runtime. All 3 certificates (CA, client cert, client key) were able to be written into...
I want to compile the ble_uart example using Segger Embedded Studio. I installed today the latest version V8.16. I am using nRF5_SDK_12.3.0_d7731ad.
I imported the project...
Hello,
I'm trying to change the name of the USB port in the "usbd_ble_uart_freertos" example code. Currently, it shows up in the Device Manager as "USB Serial Device (COM12...
I am developing a simple BLE mouse using ble_app_hids_mouse of SDK17.1.0. I found out through devzone that left mouse button click sends (1, 0, 0) and right button click sends...
I'm unable to load values into characteristics—they show up as N/A on the nRF Connect app. I tried to enable notifications using the Client Characteristic Configuration, but...
Hi Nordic Community I have a problem with the PAwR examples were I'm unable to place a sync interval bigger than 2 secs.
The example starts with an interval of 0xFF * 1...
I am working on firmware that acts as a BLE sensor hub to pipe BLE data from connected sensors to a PC over USB (using the CDC ACM UART interface). The peripheral sensors...
Hi team,
We need to interface STM32L4(Host MCU) with WT02V40V in our design.
Is UART communication enough for interface both?
And also, Is CS pin common for SPI and...
Hi Support Team
We want to use nRF7002 and nRF54L15 to implement Wi-Fi, could you provide us the hardware reference design of nRF7002 work with nRF54L15 ? Many thanks.
Hello Everyone,
I am designing the BLE peripheral which is connectable, we have our own BLE mobile application. I am trying to configure the peripheral to be visible to...
I am attempting to compile the nrf sample code for peripheral uart and I encounter a fatal error in the extensions.cmake file. Apparently the CACHE_VAR_REQUIRED is set somewhere...
