When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
Using the Zephyr how can I set a TWI module clock frequency different from the standard speeds?
With nRF SDK I was able to do this by setting "frequency = 0x00290000UL...
Hello,
I am working in ncs1.5.0 on a nrf52840dk based custom board. I have found an issue where adding a certain number of characteristics in a single BLE service causing...
I have a general query regarding using ov7670 camera module with Zephyr SDK.
I have some of these camera modules available and I would like to try out how it works using...
This question is analog to but related to a Matter application. In this case, I'd like to separate the compilation of all Matter/CHIP related application parts from my own...
I am trying to use the ICM42688 sensor on I2C BUS with nrf5340 Application core. In the configuration, the HAS_I2C_RTIO config couldn't be enabled. Is this an MCU limitation...
I am trying to run the blinky Demo on the nRF52DK on VScode, the whole process is smoothly, but it can't work, the LED no any action. could you know anything I miss? many...
When I was making the upgrade package, I encountered a problem, and there was no problem in making only one upgrade package.
It is also possible to make protocol stacks...
Hi All,
Using VS code, nr52840dk,v2.6.0sdk，sid_end_device demo, No changes have been made
Firstly, add build config
Then click on Flash
Clicking VCOM0 has no logs...
Hello, I'm using the example "smp_client_ble," and I can't manage to remove the boot message.
Below is my .prj file:
My toolchain is: NRF Connect SDK V2.2.0
I am...
The chip I 'm using is the nRF52840, the sdk and toolchain versions are both 2.5.0, my code is here :
When I call spim3 peripheral with nrfx library, I add
CONFIG_NRFX_SPIM3...
Hello, hope to find you well. I'm a beginner involved in a project that's migrating from the old SDK to NRF Connect (VSCode). The project uses nrf_crypto.h and nrf_crypto_rng...
We recently purchased the module 453-00052R from Digi-Key and have successfully implemented it into our project. The design is complete, and we are now attempting to flash...
Hi,
I am trying Asset Tracker V2 application in my custom board and rechecking results with DK to ensure no hardware reasons are there. Using SIM supplied with DK and...
Hi Support Team
Our project need 8mA charge current, how to configure charge current of nPM1300 to 8mA？ Or could you provides us other nPM chip or solution that can meet...
