I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Hi,
as soon as I include CONFIG_REQUIRES_FULL_LIBCPP=y in my prj.conf I get an error "undefined reference to `_impure_ptr'" when building:
This happens when I try...
When I developing application with nrf SDK,I can set device name by sd_ble_gap_device_name_set().
But when I turn to NCS,I should set device name such as CONFIG_BT_DEVICE_NAME...
Hello everyone I am using Nrf5340 Zephyr sdk v2.4.2 to broadcast BLE as a peripheral connecting 2 devices with Esp32 as central and phone at the same time, the following error...
Hello,
Does anybody know why I can not discover the service uuid as shown in the picture below?
I want to connect a sensor with this chip nRF52832, it's service UUID is...
Hello,
I'm using nrf52840 USB Audio headset application on nRF52840 DK. The nRF connect SDK version is v2.6.0.
I want to change the output to i2s out. The following are...
Hello, I have a few questions about sending code via J-Link. We are doing our project on vscode with 2.6 sdk. When working with nrf5340dk, flash via vscode was enough. However...
Dear lovely people from Nordic Seminconductor,
I have the nRF52840 dongle.
I installed the software ""nRF Connect for Desktop" on my Ubuntu 24.04
For that I ensured...
Hello,
I am using the NRF52840 dongle, and for my project I need to be able to send/receive data from a RaspberryPi and also send/receive large strings between multiple...
Hi everyone. I'm using nRF Connect SDK 2.6.1. I want to use Emulated RTC driver functionality.
Therefore, I configured prj.conf file as (based on This Link ): CONFIG_RTC...
Good afternoon,
For a beamforming application in the Wi-Fi range, I am planning on using an nRF24L01 to generate the signal.
The signal would later be split into N different...
Hello,
So I have an IO Shield with the nRF5340 SoC. I have connected the IO Shield to the Port 12 of the nRF5340 Audio DK as shown in the schematic:
Connections:
Debugging...
Hi,
I am trying to sniff between my phone and a BLE device.
When I put the device in pairing mode, I can see it in the "advertising" list. Then I select it (but I don...
Hello Nordic Forum, I am working on a project involving data transmission from an nRF52840 board to an Android application, and I would appreciate guidance and insights from...
Hi.
There is MainThread and MeasureThread.
There are also two events that MainThread sends - BIT(0), BIT(1). These are Start and Stop.
In MeasureThread, we first wait...
