Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I have a PPK2 on hand.
Here is what happened:
1. When I first connected it to my Windows 11 PC, the Power Profiler app in nRF Connect for Desktop detected the device...
Hello,
I have been working with the nRF9160 DK to understand AT commands. I tried flashing the Serial LTE Modem application using the Quick Start option in the nRF Connect...
Hi.
Developing PAwR in project, I have some Question.
before Asking, My Project Structure is below.
1 Gateway (Advertiser) - Node1 (Scanner)
- Node2 (Scanner)
-...
Hello,
I'd like to send/receive data over UART using the expansion board connector of my Thingy:91 X (pins 0.18 & 0.19 as RX/TX). With SB8&9 separated (to isolate pins...
Hi,
I was able to purchase a commercially available 30cm ribbon cable to connect from the nRF54L15 DK to a custom board for programming. I later realized the DK documentation...
Hello,
I have custom hardware using an nPM1300 and nRF52840, and I am having trouble getting the nPM1300 to work as described in its documentation. I have a button connected...
I am trying to write a low level driver for the TWIM system in a nrf52840 and cannot seem to get the hardware to transfer the TX data out of memory. For many reasons, I do...
I am working on project with nrf54l15dk/nrf54l15, and the project runs on cpuapp without utilizing flpr. So, I decided to release the allocated section of flpr on rram_controller...
I'm seeing an issue where nrf91 SLM, running as an AT modem over UART, sometimes chokes on XSEND command and doesn't respond until the host (nrf54) sends another AT command...
i got the following code from here: https://docs.nordicsemi.com/bundle/ncs-3.1.1/page/zephyr/kernel/services/timing/timers.html , and am using version 3.1.1 of the SDK
...
Hello, I am currently trying to use kmu to store a series of derived keys. My current systems derives AES keys and attempts to store it into KMU. As psa_key_derivation_output_key...
Hi,
in ncs3.1.1 peripheral_uart sample after disable the uart init and gpio_config, the nrf54l05 can achieve the low power state,but the avg Idle current was about 5uA,seens...
Hi! I'm currently trying to use waveshare E-Ink display module (waveshare_epaper_gdeh029a1). First of all, I wanted to test out the lvgl by flashing the sample onto nrf52840dk...
Support Ticket Draft: Severe PPP RX Buffer Overflow on nRF5340 Gateway (NCS v2.5.0)
Subject: Persistent net_ppp: Rx buffer doesn't have enough space Errors on nRF5340...
Hi
It's my first experience with nordic. I need to implement nfr 52833 with RFID-RC522 connected by SPI port. Does anyone have an example to start using the SPI port in...
