I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am working on nrf52810. I raised the RAM size in the linker file, which is larger than the real physical RAM capacity, for the testing purposes. I anticipate a hard fault...
Hi:
I use mqtt_ Sample routine: MQTT is connected to the server, and I shut down the server. At this time, the 9160 status has not been updated, but is still connected....
Hi
1、Now we connect the VDD to the battery voltage (3.4-4.2), and the VDD_GPIO is fixed at 3.3V. In order to match the GPIO of other peripheral cpus, will all GPIO be connected...
We plan to use the 52840 to make a module with an external flash, if we apply the QSPI peripheral, must we use the P0.23,P1.00,P0.21,P0.25,P0.19 pins recommended in the specification...
I want to run my software on nRF52832. It is already running on nRF52840.
What are the changes I would require making this transition.
We are using soft devices and all...
Hi.
Please help project evaluation.
The project is a BLE HID mouse , it need playback LC3 audio sound sometime.
Can we use HID function and LC3 function at the same...
Hi,
I am unable to connect and program a custom board with nRF52833 after performing 'Erase All' using Segger IDE (V5.66).
Those boards were programmed a few months ago...
Hello! I am a total newb but trying to self-learn embedded programming / electronics. I recently received a nRF52840 development kit and followed instructions at https://nordicsemi...
Development environment :
ARM-GCC version - "gcc-arm-none-eabi-6-2017-q2-update"
nRF SDK version - nRF5_SDK_15.2.0_9412b96
nRF Mesh SDK version - nrf5SDKforMeshv310src...
Burn the firmware of nrf/samples/bluetooh/multi-adv-set, the mobile phone scans the broadcast of 2 mac addresses.
How to set multiple broadcasts of nRF5340 to the same mac...
I'm trying to use BLE and radio synchronization with a nRF5340. For this I need to integrate radio synchronization and HCI RPmsg into the nRF5340 NET core. My synchronization...
Nice to meet you
What is the recommended land size for your product nRF52840-CKAA?
Mechanical information was found at the following URL.
" ">infocenter.nordicsemi.com/index...
I am trying to get the UARTE0 on the nRF9160 DK to transmit some bytes through the Virtual COM port. I am not sure why it does not work. I have included my source code below...
I followed the directions/videos to install the nRF development environment for VSCode on a Windows machine: https://www.youtube.com/playlist?list=PLx_tBuQ_KSqEt7NK-H7Lu78lT2OijwIMl...
