Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi Nordic
I downloaded nRF5340 DK Hardware files (Altium Designer files).
pca10095_sheet1 and pca10095_sheet2 can be imported in PADS logic tool.
But, files from sheet3...
Hello,
I have a problem when I send data with CDC ACM and using CLI interface my data is mixing. If I put a delay between sending data I have no problem but this solution...
Hi, I want to enter the NRF52 into a standby low power mode.
I am running sdk17.0.2, with FreeRTOS and softdevice (7.2)
The steps I take are:
1) stop all my threads...
I'm trying to integrate the following driver into my project
https://github.com/nobodyguy/HX711_zephyr_driver In order to load it I need to update the west manifest. Using...
Hello,
I am working with the nrf52840 chip, and would like to store a serial number on the device that persists across boots and OTA-DFU. I have integrated the nvs sample...
Dear All:
We run a simple message model in light_switch_client and light_switch_server code.
After provisioning the two nodes via nRFmesh app and set pubilsh in clent...
Hi,
We need to refer detailed documentation & implementation for health model struct bt_mesh_health_srv_cb
we referred to this document - https://docs.zephyrproject...
Hi, This appears to be similar to Case 232209 (from 3 years ago).
What: I am looking to have the 9160 act as a producer - sending ANT and GPS records on a regular basis...
I have a problem to advertise a service. When I include a header file, an extra service is automatically created. It seems like that the service will be advertised twice....
Hi,
I managed to do a DFU with an application on a nRF52820. Now I wanted to test if I can also update the softdevice. For this I read the following article: infocenter...
Dears,
I am developing a device base on nrf52833 SOC, nrf Connect SDK ver2.0.0.
I run the bluetooth mesh sensor server example and I want to have OTA on it.
But when...
What is the maximum time that I can use in app_timer_start?
I tried setting it to APP_TIMER_TICKS(15 * 60000) in order to set a timer of 15 minutes but it timed out after...
Hi,
I programmed network core ble5-ctr-rpmsg_3303.hex with nrfConnect programmer. I then used VS code to run/debug nrf5340_audio_dk_nrf5340_cpuap.
Please let me know why...
I've been trying to connect to a mqtt broker using the program called "mqtt_simple_sample" provided in the example files.Sadly I've been unable to get it to work.
I changed...
