I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi! I followed the recipe described on nRF Sniffer for Bluetooth LE to flash the sniffer .hex file into my dongle, install and configure the wireshard.
When I start the...
I am trying to install using VS code, using the video
https://www.google.com/search?q=install+nordic+visual+sydio+code&oq=install+nordic+visual+sydio+code+&aqs=chrome..69i57...
Hi everyone, i am new at this platform.
In my project, i need to take gps data from uart and send the data over zigbee with nrf52833. I haven't found any example and don...
Hi All, trying to find a cause of this problem, we have two devices, one is acting as peripheral and one as master.
Peripheral: ( nRF52832, s132 v7.0.1) a remote wireless...
I am trying to make a build with a slightly modified copy of the Zephyr button example on a nrf9160 board with a upgradable bootloader.
The following command can build our...
I seem to get error 4 on nrf_sdh_ble_enable when building and running the application in release mode.
Everything works perfectly when building in debug mode and I've checked...
Dear Ladies and Gentleman
Regarding the Bluetooth SIG Qualification the BQC needs a QDID for the Softdevice Controller Subsystem ( from table 2 of the compatibility matrix...
when i debug samples in Zephyr, i can see log through UART when i use "printk" function.
but i find there has "BT_DBG" and "BT_WARN" in code. so what's its using? and where...
i am receiving some packets so i need to send that packet to central device(mobile) if i send 20-20bytes it successfully sending the data to central device(mobile) if its...
Hi, i am new at nordic. I am working with nRF connect sdk. I am trying to run example applications but the code never runs. I have checked with debug and it never goes to...
I'm using NRF Connect SDK 2.1.0 and a 52840DK. In normal (non-bootloader) mode bluetooth initializes fine (bt_enable succeeds). However, when I start using MCUBoot, bt_enable...
We are experiencing connection issues for specific Android & iPhone but not for others (i.e. Samsung Galaxy S9).
Phones with issues
Android Details
Samsung Galaxy...
Dear,
I have 2 kits nRF52-DK and nRF52840-DK. I want to make simple app for sending data from one kit to another. Is it possible to use only the radio without using BLE...
