I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi all.
Las Febuary 21, I received a Product Update Notification mail from Nordic, saying:
...We've just released a new version of the nRF Connect SDK, v1.9. This release...
Hi,
I'm trying to measure the communication distance with Coded PHY using two nRF52840s and the demo software below,
but there are some problems. They are shown below...
It has been about 4 years since I was developing for the nrf52840. During that time, it seems Nordic has moved to promoting the VS Code IDE vs. Segger Embedded Studio. If...
Hello,
I'm using the file app_update.bin of my project to execute a FOTA. I know that the first bytes indicates if the file is an application firmware, modem full or modem...
I was wondering if there was any documentation (graph or otherwise) that shows the efficiency of the DC/DC converter vs. supply current.
The product spec describes the...
https://devzone.nordicsemi.com/f/nordic-q-a/70679/call-to-nrf_sdh_enable_request-fails-in-sdk-v16-0-0-works-in-sdk-v15-3-0/291135?focus=true
I've been suffering from the...
Hello,
I want to implement the interrupt functionality and based on my understanding I can implement it using GPIO or ISR function.
In case of GPIO (APIs here ):
For...
Hello,
Is there a list of Android devices that will run nRF Connect, or will it run on any Android device?
Which Android app stores is it available in please?
Kind regards...
Hi,
We are using a module which includes nRF52832 in a custom board. After a while devices stop working but when we re-connect battery device starts working again exept...
Good morning,
I get a i2c nrfx twi error on startup and reset whenever the i2c sensor is switched off (<err> i2c_nrfx_twi: Error 195952641 occurred for message 0). I am...
Dear all,
I would like to ask if the nRF5340 LE audio can connect to a mobile device while another LE device is also connected to the mobile.
For example, is it possible...
Is it possibe to configure uart with baud rate of 512 on nrf52832?
I tried to configure the uart with this baud rate, but I am not able to get the uart communication ...
Hello everyone i need to update the Advertising Data of the device but i am not sure the correct way to do it. First i have the next struct of the Adv Data that i want to...
Thank you for your help. We are currently developing hardware using nrf52840. I would like to use pin numbers to control LED lighting, but when the port number is 0, I can...
I am developing a custom application that was started from 1 of the bluetooth examples for a customer and though I have been using the same custom PCB for 7 months, I am now...
