I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hello Nordic：
I wanna to know what actions a thread have done from reset to joined a thread network.
I observed the air packets by using Wireshark. I found a router(rx_on_when_idle...
The device is connected to the PC via FTDI chip. The device manager shows the COM port. LTE Link Monitor v2.0.1 cannot find the connected device on SELECT DEVICE. The windows...
Hello.
I am using nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral and developing.
I am using nRF Connect to communicate with the peripheral nRF52832.
One of the...
Hi,
I have tried to follow the below tutorial ( https://www.youtube.com/watch?v=hY_tDext6zA&t=933s) . While I am trying to advertise the ble by following that webinar. I...
Hi,
I want to use BLE as both connectable mode and non-connectable mode in the same application. Is it possible to do that?
Is it possible to switch connectable BLE mode...
Hello!
I have a nRF52840DK with a custom board. I have installed nRF 1.9.1. I have read about the twi_scanner but I don't find that code in my installation! Did I do anything...
Hi,
I am trying to download SUPL client library but got an email that my request was denied. I've used the same email address as the one here. Can you please advise?
Kind...
i need help.
We use nrf52840 and DK17.0.2
Using saadc with oversampling x8 , Single-ended mode.
Question
When Event monitoring using limits , Is the timing at which...
I'm using three low power PWM instances driving three separate IO pins open an nRF 52810 and need to be able to re-configure each of the channels on the fly to select opposite...
https://devzone.nordicsemi.com/f/nordic-q-a/69596/device-initialization-problems/285611#285611
had gone through above thread.
I am struck exactly at this point.
i...
Hi
I am using 52832 peripheral role.
sdk16.0
ble_uart add one character 0xff03 which have notify attribute
have these function
1. Use connectable broadcast on no...
Dear Nordic Engineers
I study central code,I find a param ble_gap_evt_adv_report_t
I can understand other param of ble_gap_evt_adv_report_t,but I don't understand set_id...
The NFC pins of my nRF52840 MCU have been set to be used as GPIO pins through the NFCPINS register. I can toggle the GPIO lines just but I find that after power on that the...
Hello,
been trying to add lte_lc_connect_async(lte_handler) to mqtt_simple, just like the way it is in sample aws_iot. Instead getting a failed response.
Now not sure...
