Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
environment:
SDK14.2 Project: ble_app_uart
I am sure that the problem occurs in uart_module.
Uart use the app_uart_put to send the first byte successfully, then it will...
We have already developed a wireless sensor application based on the ESB protocol.
Now we want to increase the range by adding an nRF21540.
We started by testing the sample...
Hi,
Is there a possibility of race condition when writing and reading using nrf_fstorage_write and nrf_fstorage_read?
I have a very strange bug, when writing to an address...
I am using VScode's extension for nRF connect. I have been using it to flash program with the 52DK and 9160DK previously. Now under the connected devices tab nothing shows...
Hi,
I'm using the GPIO mode of CAF leds module to control led.
LED_EFFECT_LED_BLINK or LED_EFFECT_LED_BLINK2 macro can be used to set the effects of led. But the loop_forever...
I encountered problems in developing nrf5340 with nck v1.5.0.
I use nrf_rpc_tr_init(rpc_receive_handler) to initialize an RPC and IRQ_DIRECT_CONNECT(I2S0_IRQn, 0, custom_i2s_irq_handler...
The solution seems to be built for a Production rollout for organizations with resources, but not so much for devs on a tight budget.
The actual bridge build is quite extensive...
Hello,
I'm using nRF52840 and nRF Connect. I've customized hello_world sample from Zephyr to also work with mcumgr and receive and respond to SMP commands such as "echo...
Hi,
I have been using an UART connection for serial communication but it stops working when I enable the Bluetooth module and initialize it. The error I receive is the same...
Hello, in an effort to downsize the EC2 instance from t3.small to t2.micro (nrfcloud-mqtt-bridge/MqttBridgeCluster/DefaultAutoScalingGroup), the bridge instance is detached...
I have adapted and incorporated the NCS OTA DFU sample into my project. Initially, FOTA updates have been working. Now, after pushing an update, the image is stuck pending...
Hi,
We are making software for our custom board based on nRF52833 and nRF5 SDK 17.0.2. We use app_uart for our serial communication in active mode and in sleep mode we disable...
I'm trying to build a basic shell sample on a custom board based on nRF52840
In the proj.conf file I have
CONFIG_SHELL =y
CONFIG_SHELL_GETOPT =y
CONFIG_SHELL_BACKENDS...
I am new to Zephyr and I have been trying to get hold of a tutorial or a sample app that would indicate how I can use the UART on the nRF52832 for communications with another...
Hi,
I'm wrapping up a project which uses an nRF5340 as both a Bluetooth peripheral to advertise etc and also as a Bluetooth central to scan for devices (not both at the...
