I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hello, I tried building the app showcased in this example: https://www.novelbits.io/smart-ble-lightbulb-application-nrf52/
I have gotten everything to build fine except...
Hello,
I need some help or advice on the easiest way to perform DFU in a nRF52832 device using a nRF52820 as a central through BLE. My nRF52832 device already has the DFU...
Hello, All
I am evaluating the example, following the instruction information here https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v17.1.0%2Fble_sdk_app_nus_eval...
Dear Support
Try to modify this use UART_1 for sending out data received via BLE, which is pin P0.14 on nrf52833dk_nrf52833, I modified Kconfig file under the boards folder...
Hello everyone, i am developing a board based on the nRF52832 microcontroller SDK v16.0.0 and sd132 for sending data of a sensor over BLE to a mobile APP. For this i am using...
Hi,
I'm implementing a hard real-time system (few us jitter) on nRF52840, SDK17.1, based on FreeRTOS project.
In the project, I need to sync GPIOs toggling with ADC...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
Is it possible to "WRITE" a characteristic that is larger than the MTU? As an example, we are considering the following...
Dear All,
I am looking for sample code to use an external QSPI flash (MACRONIX MX25R6435FZAIL0). The code is run an nRF52840 based custom board.
Your help is appreciated...
Hi,
I have a doubt regarding the possibility of removing or disabling an endpoint at runtime.
Assuming that we have a device with multiple endpoints, is there a mechanism...
Hi,
I have problem with program nrf21540 UICR mode. POUTA/B_UICR seem not set successful during measured here.
Below following which I write via SPI(Voltage is 3.5V)....
I am trying to use the nRF52840 Dongle as a controller with the Pi and ping devices (e.g. using l2ping to ping my phone)
I have flashed the bluetooth hci_usb sample on to...
Hello,
I am very new at this. I have just started to work with the nrf9160DK board, I am using modem firmware 1.3.1, and nRF Connect SDK 1.8.0. I am trying to test asset_tracker_v2...
Current result:nRF dongle is disconnecting with wireshark and Green led also stopped blinking
1. insert nRf dongle and open wireshark
2. Select nRf dongle(Green LED is...
I'm having an extremely annoying problem. I have an application that uses Nordic NUS service.
(1) I created it from the peripheral UART example for NRF52-DK, and adapted...
Hi.
I'm using PDN example code on zephyr nrf sdk. Please take a look on below log.
Can somebody help me to figure out what are the API can be used to send and receive...
