Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi all, im asking question about triggering my own antenna. there's few questions about it. 1. im using TI boostxl antenna array (3 antenna) , periodic table are as follow...
Hi,
I want to use the 64MHz crystal oscillator (HFXO) as the source for HFCLK clock controller. How can I need to enable or disable the item in KConfig on nRF Connect SDK...
Is there a current example for nRF52840 power management under Zephyr / nRF Connect SDK?
Searches for this turn up old examples, such as this one , that are no longer in...
Hi Nordic,
My customer want to know, whether LLPM function and Multilink can coexist?
For example, when I use a central to connect with 4 peripheral devices, can I use...
Hello,
NCS1.8.0 Windows10 X64;
i2s test,see the source code ,
it runing ok;
but,when i change to timer send,got error.
i want to send data by timer,
source...
Hi Team!
I am trying to connect the Thingy 91 to nRF Cloud using a local provider (Vodafone Romania). I followed the getting-started video when setting up my device. However...
Hello,
I need to power the nRF52840 with 1.8V while keeping it connected to SES through USB.
I believe I have to proceed as directed at User Guide paragraph 8.3.5 “nFR52840...
Dear Concern,
We are currently planning a mass production of a product that uses nrf52840 USB dongle as a component. We are thinking of using JTAG debugger to flash the...
Hi,
I am getting a strange issue in my code where my FDS will run fine if there is no bootloader but fails to initialise if there is a bootloader present. I am using SDK...
Hi!
We are testing nRF9160 in an application were we monitor sensor in certain modules on trucks / trailers. Our test application is based on the Serial LTE sample application...
Hello,
I am new to DFU OTA on Nordic's chips and I am currently trying to implement it on a custom board with an nRF52832-QFAB chip.
This will be a long issue since I...
Dears,
I can't select a new operator among the list I have, when I put the command at at+cops=1,1,"20820" , I have the error: ERROR: -8 , could you explain me what is this...
Hi, I am facing an issue, I am developing nRF9160 based Product, get sensor data from peripherals and publish to AWS cloud.my firmware is based on AWS IoT sample. I observed...
Hi,
With my company we want to develop an embedded application with Direction Finding. Do you have any examples to give us to start the development? For this project we...
Hello. I would like to ask a question about a problem I had in implementing the battery voltage monitoring function.I am trying to read out the battery voltage using the following...
