Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hello, i have send my program with my DKnr52840 on my module 805, (the example peripheral Uart) now i would like to make my com with putty or other software but i'm going...
Hello,
The company I work for uses an nRF52840 PCBA for one of its project. During production, the board will be placed under test using a custom-built fixture. Due to the...
Hi,
For my application I am supposed to evaluate if nordic SPIM & SPIS drivers are working on interrupts..? In the driver file "nrfx_spim.c" I observed the below code...
Hi,
I have some questions regarding DFU:
Does it have its own BLE hardware?
Does it have its own processor? Or it's part of the main one?
Can we synchronize between...
Hi all,
struct spi_config {
uint32_t frequency ;
uint16_t operation ;
uint16_t slave ;
const struct spi_cs_control * cs ;
};
in documentation, it says...
Hi I am recently working on Enhanced Shock Burst (ESB) protocol. where PTX and PRX
and
PRX will communicate upto 8 PTX
i have a question like how a single device will...
I'm working on porting some Arduino code for a Crystalfontz 320x240 FT810 display to run on the nRF9160DK. I'm having some success, But it seems Zephyr has an FT8XX driver...
I use a example application from SDK_DIR\examples\ble_peripheral\ble_app_template\pca10056 base on nRF5 SDK v17.1.0,then use SDK_DIR\examples\dfu\secure_bootloader\pca10056_s140_ble_debug...
Hello there, my application needs to switch master/slave roles after the connection established.
As i know, the initiating device will be master every time in BLE. From...
Hello.
I am developing nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral.
I am creating a characteristic using characteristic_add. I want to set the attribute handle...
Hi
1、 A customer wants to evaluate the keyboard that can run ble and mesh simultaneously with nrf52 chip.
2、I found mesh example in both NCS and nrf5_SDK_for_Mesh_v5.0...
Hi, I am working on this project where provsioner provisions all the unprovisioned devices (nodes) and then sends the LED's data (containing brightness, intensity and pattern...
Hi, I tried running an spi sample program with code as in below, shorted the MOSI and MISO pins and data was visibly received in print statement:
While in the same code...
