When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
I have been using the nRF52-DK for while and it been good.
But when I accidental hold the "BOOT/RESET" button, the board now stop working. only LEDs is blinking (per sec...
I would like to ask if someone from India ever used Thingy:91? Which SIM card is used or where to get the supported SIM card? How to get it working in India?
In VS Code, when pushing the " Connect To RTT In nRF Terminal " button, a message shows up:
J-Link V7.20 Device Selection The selected device "NRF52832_XXAA_REV2" is unknown...
Goodday all
Im trying to drive some Neopixel LEDs with 52840DK SDK_17.1.0. and have been following this example. https://devzone.nordicsemi.com/f/nordic-q-a/70560/nrfx_i2s...
I'm trying to install and run the nRF Command Line Tools, but am running into issues. I was able to successfully install the Linux32 version of the tools, but when I go to...
Hi
I am using nrf52840 and I want to use nrf_calendar example with app_ble_uart,
I am traying to send parameter from nrf toolbox uart app mobile
but I have no idea how...
Hi,
I am using nordic 52840 development kit along with sdk17.1
I am tried to use ble-uart example code to receive data from the app and based on the data i need to write...
I'm trying to follow the instructions to perform an OTA DFU for the Thingy 52.
https://nordicsemiconductor.github.io/Nordic-Thingy52-FW/documentation/dfu_generating.html...
I'm using SDK 1.7.0. Here's how I have the modem code setup.
Init modem outside of thread loop
Set modem at+ comman CFUN=1 (start searching for a tower)
Once +CEREG...
hi,
when I call 'mesh_stack_device_reset()' function from the application, then the bootloader goes into infinite loop.
exactly at the point int the main() -> init_clock...
We are supplying the nRF52840 from 5 V into the VDDH pin. We are not using the USB interface, so I want to confirm what our options are for the VBUS pin. Can we leave it floating...
Hi,
I am trying to include the CMSIS-NN libraries inside the segger project. Since they are not available in the software package inside Segger Embedded Studio, I pulled...
Hello! I've been using Segger Embedded Studio (Nordic Edition) for the project in nRF Connect SDK.
So, this SDK uses CMake to build the projects. But my project involves...
