I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,
I'm trying to do some calculations using the FPU, but it seems like software float routines are still being used. I haven't been able to find any conclusive documents...
I'm trying to generate a service key and token so that I can access AGPS services on nRF Cloud. The documentation says that clicking on 'Device Management' the panel that...
Hi
I tried to run the sample "hci_pwr_ctrl" from the NCS v2.7.0 on the nRF54L15.
After starting the sample, the modification of the TX power level during the advertising...
TWI Master drives BNO085 to read four-element data at intervals of 20ms, and I2C will not be able to read data when the device works for more than 10 minutes. INITTWI and...
I have verified The maximum channel table size NRF_GZLL_CONST_MAX_CHANNEL_TABLE_SIZE is 32.
but result_value = nrf_gzll_set_channel_table(my_channel_table, 32) return false...
Hi, I am trying to reach the highest possible throughput when sending data over usb to nRF52840 from a host computer, but I am reaching 4Mbps max. Is this reasonable or is...
Hello!
I am using a nRF52840 board for some really simple development. First I just tried to run the blinky example and connected with another BT device. It worked well...
Hi there,
I am seeing inconsistencies with the PCB layout specification of the nrf7002.
1) In the v1.1 of nrf7002 datasheet, it is recommended that the following capacitors...
Hello,
I am working on creating a custom board based off the nrf5340dk_nrf5340 board
I am following the tutorial here
https://academy.nordicsemi.com/courses/nrf-connect...
Hello,
I would like to know if there is official C# source code to perform DFU OTA for a NRF52840 from Windows without Nordic hardware (DK, dongles etc..), using only the...
Hello,
after an attemp to switch to UF2 Bootloader from Open Bootloader my Makedriary nRF52840 MDK USB Dongle stopped working (now shows only the green led always on) and...
hello,
I would like to know which operations were performed on all chips by the `nrfjprog --recover` command.
"The nrf52833-B chip is by default enabled for read protection...
Hi
I am getting an error while building source code. The same code used to build while using NRF connect SDK version 2.5.1. Currently I am using nRF Connect SDK version...
Hi,
I followed the steps below and the error "zephyr\zephyr_pre0.elf section 'text' will not fit in region' FLASH'" appeared when I compiled. I did not change any code....