When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I'm using Windows 10, Wireshark 3.2.17, python 3.9, pyserial 3.5.
I see this question has been asked before but the solutions did not work for me.
I get the...
Installed pynrfjprog on Ubunto 20.04 (native) via pip. Can open Highlevel api etc, however fails to detect nRF52 dev board as s probe and the logs indicate DLL failure.
...
I'm sorry, I don't know how this is reproduceable.
Yesterday and today my connection does not work. Sometimes . Yesterday it was OK early in the morning and in the afternoon...
I am using the SDK v17 with the Mesh SDK v5 and the nRF52 development kits and I'm using SEGGER.
SETUP: I have a mesh network with: 1 dimming client
1 dimming server ...
Hey Guys, currently, I am working on my masterthesis. I have to develop an mobile application which comminicates with the nordic board via BLE. I know that there is an existing...
Can you please clarify the typical eSIM current consumption when using eDRX?
Is the eSIM module on all the time? If so, what is the typical consumption?
If possible to...
The code shown below filters the duplicate MAC addresses, but I found in the previous development process that many Bluetooth devices only display the MAC address, not the...
Hii all,
i have a NRF52832 board with some sensors ..I coded it with SEGGER Embedded Studio . i Build and flashed and RUN successfully,
But after Disconnecting the board...
Hello , I am using the DTM in the NRF Connect.
Does you packet count preforms any CRC or other verification when receiving packets? I can not find any mention of BER (Bit...
Hello , I'm using nRF52832 DK and running the ble_app_multilink_central example . Here i want the list of beacons and get data from the specific beacon . I tried changing...
Hi, I am looking into combining SHT85 into Light lightness Server (mesh v4.2.0) code using nrf52840-DK. For my working SHT85 code, I am using an LCD to display the temperature...
Hello, this is Kwonjoon Lee. I have a problem of PC-BLE-Driver (C/C++ library) installation.
I am following installation guide which is written in the https://github.com...
Hi!
When reading the documentation of the I2S peripheral of the nRF52840, I don't see how to stop the transfer after the last data block. Figure 2 only shows how to start...
Hi,
I used the BLE blinky app on a nRF52832DK and it was working nicely.
I am then trying to make it run on a custom board with nRF52832QFAB version mounted.
I see several...
