Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi Nordic team
Last week and before, I tried sdk connect v3.0.0 http_application_update example.
Everything was fine. Pressed button1 to download new bin file and then...
HI DEV
Currently we found a UART Frame error on customer product:
Application scenario diagram
Figure1
nrf52820 ,SDK17.02, softdevice:S132 , gap event length=6*1...
Hi! I'm new to zephyr and nRF boards.
I am trying to write a custom board using the nRF52811. When I try to build examples using the custom board using the command (syntax...
When I asked earlier, it was not possible to send HTTPS payloads greater than 2K due to the TLS secure socket buffer size limit. I see in the most recent modem firmware release...
I'm using nrfjprog version: 10.13.0 / JLinkARM.dll version: 7.50a to flash a firmware onto a custom PCB with nRF52840. Programming hardware is a nRF52840 DK. Our firmware...
Hi,
I am sensing interrupts on a pin using GPIOTE. I can see the interrupts coming on the oscilloscope. The firmware also detects the interrupts. However once I am inside...
Is the IXIT for RF of nrf52832 correct bellow? The test house said the value of inband image frequency should 4Mhz.
IXIT for RF
IXIT Reference
Identifier ...
in \nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\zigbee\experimental\cli\cli_agent_router example , we use the nrf52840 dongle as the Coordinator, for joining the...
what happened when I create a kernel timer (based on the 32k RTC) by nrf connect sdk on nrf 52840 dk?
static const struct k_timer my_timer; static const struct k_work my_work;...
Hi All,
Im pretty new to embedded systems and currently trying to connect a TE MS5837 30B pressure sensor to a nRF52840DK (pca10056) which is all being done via Segger ...
Hello,
I am using openocd to flash nRF52 DK, however, I have several devices connected to my pc at once and I can't figure out how to flash just one of them, When a single...
I need to call the API: clock_control_on( const struct device *dev, clock_control_subsys_t sys)
located at the SDK path ncs\v1.6.1\zephyr\drivers\clock_control.
...
Hi, I am communicating SIM808 with nRF52840. I have made changes in libuarte example and send AT commands to send SMS. I have the following question.
How can I know that...
