I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hey, I was trying to look for information on how nrf9160 modem selects the network to use, since we are having slight trouble with some devices triggering full network re...
Hi,
I am testing the radio_test (short-range) sample on an nRF54LM20A DK . The test setup is:
Board: nRF54LM20A DK
Sample: peripheral/radio_test (NCS version...
Hi all,
I'm working with building/programming v3.1.1 SLM application for my nRF-9151, it all goes well while testing with nRF-9151DK.
But when I want to try my custom...
Dear Nordic Team and Distributors,
For nRF54L15 (CSP and QFN) design circuits, how to optimize the stable modulation issue?
What aspects should we consider to do failure...
Hello Nordic team,
We are evaluating nRF54L10 for a battery-powered Bluetooth LE medical device .
We are considering the nRF Connect SDK Bare Metal option instead of Zephyr...
Hello! We are in the middle of an upgrade to 3.2.1, and we encounter the following issue using SB_CONFIG_MCUBOOT_MODE_SWAP_WITHOUT_SCRATCH, SB_CONFIG_MCUBOOT_MODE_SWAP_USING_MOVE...
Greetings,
I'm considering nRF52840 for a product. My connectivity requirements are BLE 5+ (For GATT-based communication, No requirement for channel sounding, etc), USB...
Hi,
working on custom bootloader on nRF52840 with S140 v7.2.0(not enabled in bootloader) with SDK.
This is code for erase and write:
Now, when writing I get prints...
Hi there! I am trying to set up external flash (w25q64) with my NRF52840 project over SPI. I have adapted the spi_flash sample in an attempt to set up this device, but I am...
Hi,
nRF9151 + Kyocera AVX P822601 internal SMT antenna: 8 dB RSRP loss vs external antenna — possible PCB layout issue?
Test Results
Test 1 — Out of Faraday cage, internal...
Hi everyone,
We recently started to add the iBeacon broadcasting to our own BLE project that runs on an nRF5340. It is based on the code from the sample of the SDK (we currently...
Saw this post from about 1 year ago.
Any updates regarding USB host firmware support on the nRF54LM20 or any timeline for when it is expected to gain some level of support...
Hello, I wanted to update my project (Custom board using the nRF54L15 ) to the v3.3.0 SDK since this fixed a BLE bug with the v3.0.1. version. To my knowledge I did not change...
Hello,
First of all, I'm delighted to have found the beginning of eMMC support for Nordic devices as software peripherals in NCS 3.2.0: https://docs.nordicsemi.com/bundle...
