Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi, With nRF5340 DK, I am using CC registers of NRF_TIMER2 (as a free-running Timer), and DPPI, interacting with Radio. I set up a Timer Compare (functioning as a timeout...
Hi, I am having trouble setting up the partition manager in external flash with nRF54L15dk in NCS 3.0.0. I did not find any examples of this working. Interesting thing is...
1、How can I find the QEDC configuration for NRF54L15 or the QEDC demo? I found that Nordic courses do not offer these options. 2、Another issue is that I am using QSPI routines...
Hello,
If I set the connection interval to 300ms, can I call bt_nus_send multiple times (e.g., every 100ms) within that interval?
Additionally:
How can I check if...
Hi,
As the subject says, is there any way to get satellite count through at commands while using the AT firmware on NRF9151?
I'm currently using AT firmware version 2...
Hi
Is there a undocumented register to control the CC1/CC2 inputs?
Many power-banks switch off it's output if the current falls below a certain value (e.g. when the devices...
I am wanting to use the castellated pinouts on the nRF7002 expansion board.
I have the nrf7002eb.overlay file open and it has defined two pins that do not make sense to...
我们自己用nRF54L15做了一个硬件，和Android BLE调试助手链接都正常， 和电脑端连接大概有30%的概率能连接成功 我用的是主要报错是Failed to subscribe to characteristic: 6e400003-b5a3-f393-e0a9-e50e24dcca9e. 订阅读取数据特征失败
Hi
When l was using the function ble nus_c_string_send0 for datatransmission, an error occurred. The error code was 0x00000008.And at this point, the system resets.l don...
name:
Code:
Log1：
When the storage capacity is 64 entries, continuously reading 32 of them takes about 2 seconds.
After changing the path, run the write and...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
For the Pawr example I refer to E:\NCS\v2.8.0\zephyr\samples\bluetooth\periodic_adv_rsp and periodic_sync_rsp.
I need...
I cloned a project( https://github.com/pstrueb/hci_uart ) from GitHub and added conf files to the project. How do I know that these conf files were compiled correctly?
