Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi everyone,
I am following this video step by step to create my custom board configuration https://www.youtube.com/watch?v=KSivO9Cf1TE&t=474s .
I follow every steps but...
Hi all,
My project can be built and run correctly on NRF SDK 1.5.0,
after updated to SDK 1.6.1 and rebuild, it failed and messages below:
Is there any idea for this...
After installing nrfConnect SDK v1.6.1 on MacOS ( Big Sur 11.5.1 ) using Toolchain Manager, I can't find nrfjprog.
When I try and run nfrjprog in Terminal, I get: "zsh:...
Because some IOS devices support up to 185 Bytes MTU, Android phones 247.. is there
any possiblitly wow the Application Core NRF53 can retrieve the current MTU Size from...
Hi
I am working on a nRF52840 using Zephyr as OS.
I have setup some control GPIO pins in the device tree (se below). This works fine from the application. I can access...
When I enter 100 as the size for the ATT MTU all works perfect, but when I choose a larger number like 250 as ATT MTU, sd_ble_enable() does not return an error and I can debug...
I will be using an NRF5340-DK for starters. I have a Linux SBC that will be running blueZ. I can use USB, UART, or SPI to connect the NRF5340-DK to the Linux SBC. I am assuming...
Hi Dev Team,
I had installed the newest NCS version NCS v1.6.1 and was importing my application from 1.5.1 to 1.6.1.
However, I noticed a lot of changes with respect to...
Hi,
I have a question ,According to the official tutorial，I succeeded BLE OTA DFU in windows system by nrfutil ,however, when I use the nrutil tool to update the firmware...
I have tried to use I2C but it does't work out. nRF9160 doesn't start booting after executing "build and run" and pushing the reset button.
I open secure_boot project...
Hi Nordic team
At sdk connect sample/mqtt_simple, it called lte_lc_init_and_connect() to connect NBIOT or LTE-M.
If this call was not successful, could we read error code...
hi support team,
very strange question from customer
customer set up one interrupt with following code:
void gpio_wakeup_init(void) { uint32_t err_code; if (!nrf_drv_gpiote_is_init...
Hello, I am routing the NRF52840-QIAA chip and wanted to avoid the costly via-in-pad process.
Can I use the following pins for QSPI quad mode?
Also can i leave the RESET...
I have a working set of implementations placed in the 17.0.2 SDK examples directory. The projects use SoftDevice s140 for BLE and flash write operations. I would like to know...
I'm looking to enable the flash protection for an nRF52 application running on Zephyr RTOS:
Basically looking to disable flash reads from the JTAG/SWD interface: Only...
