Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Dear Nordic Engineers
Our customer uses NRF52810 with a PA chip, the model of the PA chip is RFX2401C. The attachment is the manual of the PA chip. The hardware connection...
Dear Nordic,
We use CONFIG_BT_CTLR_DATA_LENGTH_MAX definition set to 251 in our project to be able to send large data packets. Still, when migrating to nCS 1.6.1, we've...
Hi, Nordic team!
I want use RTC with Prescaler 32765 for generating Tick event with 1s interval. Could you help with calculation of jitter for Tick event in microseconds...
Hi,
I need to reduce the consumption of the peripheral_uart sample on a nrf5340dk, I use nRF Connect SDK V1.5.0.
At the beginning, I measured with an ampere meter 591uA...
When I program my external board via the nrf52dk the programming is much slower then when I program the nrf52 chip on the devboard. Is this normal behaviour and if not how...
Hi,
I'm evaluating a wireless microphone scenario, using 52's I2S and external ADC chip to sample sound signal, and than wirelessly transmitting it to another 52 for receiving...
Hi,
sorry if this is a trivial issue, but I've been strugling with this for a while, so I decided to just ask for help.
For context, I'm trying to create an application...
I have devices within an same group that bind with same app key, all are working normal together. But I want one device to be unbind and bind with another app key(out of the...
Hi everyone,
Hope you are doing well!
I am using BLE and FDS simutinuously but since they share the same interrupt priority (SD_EVT_IRQn = 4), fds events will be blocked...
I am currently running some tests on the Legacy DFU protocol and notice that even valid firmware images are unable to be transmitted. My setup is as follows:
Peripheral...
Hello,
As shown in the question. I am testing the ncs bootloader b0 and mcuboot, but I don't know it's ok or not.
work condition
ncs: 1.6.1
board: PCA10056
I am...
Hi
I have a strange question to ask for your help.In my program, I define and use a large number of global variables. However, when I define a global variable again and...
Our application frequently changes the channel table when we find interference in multiple channels. So changing channels frequently (because of high interference) causes...
Hi,
I'm evaluating BLE power consumption with a PCA10040 nRF52DK and a PPK, I cut SB9 and did nothing else with DK.
No peripheral is used in projects, Buttons or LEDs...
Hello
I've read several post about the problem regard the printf and float numbers, such as this ( https://devzone.nordicsemi.com/f/nordic-q-a/30535/nrf52-printf-float-in...
