When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I found I APPCPU3 is 0.3mA higher than I APPCPU5 . I have no idea. How come CPU consumes more power utilizing HFXO64M, an external oscillator 64MHz, than utilizing a...
Hi all,
I would like to check and see if its viable to keep radio on TX_ENABLE throughout the radio's operation, ie keeping TXEN = 1 ; at all times or keeping radio only...
hello,
i find a mistake line 62
"ldr r0, =%4 \n" ->>>>> The '=' should be removed .
void app_error_handler(ret_code_t error_code, uint32_t line_num, const uint8_t...
modem fw 1.3.0
ncs 1.5.0 and master
I am trying to test modem firmware upgrades using the lwm2m client sample and every time it is writing the 20% downloaded chunk, the...
Hi, I am following the tutorial and have some questions during the implementation.
devzone.nordicsemi.com/.../nrf-connect-sdk-tutorial---part-2-ncs-v1-4-0
A red led...
Hello There,
So basically I need to send and receive and data from to Serial Terminal via FTDI module to nRF9160 DK. So for this I am using ncs\v1.5.1\nrf\samples\peripheral...
Hi.
After updating Programmer of nrfConnect to v1.4.9, I have not be able to "execute Erase All" command.
Error message is "Error: Error occured when program. Errorcode...
Dear Nordic,
how to set UART/USB console output to be non-blocking? We use printk() to output some debug info to USB console. When the USB isn't connected, the program stalls...
Dear Nordic-Support-Team,
I (software developer) work together with an electrical engineer to develop a device, which will incorporate the nRF9160 SiP. The firmware/application...
Dear Nordic Engineer
I currently have a project that requires 5340 to act as an MCU. I also need to plug in a FLASH, which is 4GBIT NAND FLASH. Is there an example of supporting...
Hi :
nRF52832 PCA10040 DK burn this link hex code: https://www.nordicsemi.com/Software-and-tools/Development-Tools/nRF-Sniffer-for-Bluetooth-LE/Download#infotabs
Can...
https://devzone.nordicsemi.com/f/nordic-q-a/49269/long-range-nrf52840-central-can-t-connect-with-peripheral-in-ble_gap_phy_coded
due to this problem recently I have problem...
